IBM EM78M611E Network Card User Manual


 
EM78M611E
Universal Serial Bus Series Microcontroller
38
Product Specification (V1.1) 11.22.2006
(This specification is subject to change without further notice)
Binary Instruction Hex Mnemonic Operation Status Affected
0 0001 10rr rrrr 01rr DECA R R-1 A Z
0 0001 11rr rrrr 01rr DEC R R-1 R Z
0 0010 00rr rrrr 02rr OR A,R A VR A Z
0 0010 01rr rrrr 02rr OR R,A A VR R Z
0 0010 10rr rrrr 02rr AND A,R A & R A Z
0 0010 11rr rrrr 02rr AND R,A A & R R Z
0 0011 00rr rrrr 03rr XOR A,R A R A Z
0 0011 01rr rrrr 03rr XOR R,A A R R Z
0 0011 10rr rrrr 03rr ADD A,R A + R A Z, C, DC
0 0011 11rr rrrr 03rr ADD R,A A + R R Z, C, DC
0 0100 00rr rrrr 04rr MOV A,R R A Z
0 0100 01rr rrrr 04rr MOV R,R R R Z
0 0100 10rr rrrr 04rr COMA R /R A Z
0 0100 11rr rrrr 04rr COM R /R R Z
0 0101 00rr rrrr 05rr INCA R R+1 A Z
0 0101 01rr rrrr 05rr INC R R+1 R Z
0 0101 10rr rrrr 05rr DJZA R R-1 A, skip if zero None
0 0101 11rr rrrr 05rr DJZ R R-1 R, skip if zero None
0 0110 00rr rrrr 06rr RRCA R
R(n) A(n-1),
R(0) C, C A(7)
C
0 0110 01rr rrrr 06rr RRC R
R(n) R(n-1),
R(0) C, C R(7)
C
0 0110 10rr rrrr 06rr RLCA R
R(n) A(n+1),
R(7) C, C A(0)
C
0 0110 11rr rrrr 06rr RLC R
R(n) R(n+1),
R(7) C, C R(0)
C
0 0111 00rr rrrr 07rr SWAPA R
R(0-3) A(4-7),
R(4-7) A(0-3)
None
0 0111 01rr rrrr 07rr SWAP R R(0-3) R(4-7) None
0 0111 10rr rrrr 07rr JZA R R+1 A, skip if zero None
0 0111 11rr rrrr 07rr JZ R R+1 R, skip if zero None
0 100b bbrr rrrr 0xxx BC R,b 0 R(b) None
2
0 101b bbrr rrrr 0xxx BS R,b 1 R(b) None
0 110b bbrr rrrr 0xxx JBC R,b if R(b)=0, skip None
0 111b bbrr rrrr 0xxx JBS R,b if R(b)=1, skip None
1 00kk kkkk kkkk 1kkk CALL k
PC+1 [SP],
(Page, k) PC
None
1 01kk kkkk kkkk 1kkk JMP k (Page, k) PC None
1 1000 kkkk kkkk 18kk MOV A,k k A None
1 1001 kkkk kkkk 19kk OR A,k A k A Z
1 1010 kkkk kkkk 1Akk AND A,k A & k A Z
1 1011 kkkk kkkk 1Bkk XOR A,k A k A Z
1 1100 kkkk kkkk 1Ckk RETL k k A, [Top of Stack] PC
None
1 1101 kkkk kkkk 1Dkk SUB A,k k-A A Z, C, DC
1 1111 kkkk kkkk 1Fkk ADD A,k k+A A Z, C, DC
Note:
1
This instruction is applicable to IOCx only.
2
This instruction is not recommended for RE, RF operation.