Filter
Top Products
13
Operation guide
Shows the buttons for
each operation.
NOTE
• The menu automatically disappears in about 30 seconds after the last menu operation.
• Some items may not appear on the menu depending on the input or the input signal. These items are not available.
REMOTE SETTING
Setting for the external control
Item To do Setting value
SERIAL TYPE
Select the input terminal used for an
external control.
RS232C, RS485
PARALLEL TYPE
Select the external control method for
MAKE/TRIG. terminal.
MAKE, TRIGGER, SET
PORT F1, PORT F2,
PORT F3, PORT F4,
PORT F5, PORT F6
Assign the control functions to the pins
of MAKE/TRIG. terminal (1 to 6) when
selecting “SET” in “PARALLEL TYPE.”
COLOR OFF, ASPECT, A.MARKER, S.MARKER,
TIME CODE*
1
, 1:1, SCR CHECK, I/P MODE,
SDI 1*
1
, SDI 2*
1
, DVI, COMP./RGB, VIDEO 1,
VIDEO 2, EXT.SYNC, TALLY, TALLY SEL, MONI.
NAME, MUTING, MARK.SEL, L.METER*
1
,
STATUS, – – – (no function)
INFORMATION
Setting for the information display of the monitor
Item To do Setting value
MONITOR NAME
Choose if the name entered in “CHARACTER SET.” is displayed on
the screen (☞ “About the Status Display” on page 7).
OFF, ON
CHARACTER SET.*
2
Enter an optional name for an input video source (10 characters at
maximum).
☞ “Technical
information”
STATUS DISPLAY
Choose if the information of the current input is displayed on the
screen (
☞ “About the Status Display” on page 7).
AUTO, OFF, ON
CRC ERROR*
1
Choose if the CRC error indication for the input HD SDI signal is
displayed on the screen (
☞ “About the Status Display” on page 7).
OFF, ON
SUB HOUR METER
Display the total hours of use (unit: hour). You can reset this HOUR METER.
MODEL
Display the model name of the monitor.
VERSION
Display the version of the monitor.
HOUR METER
Display the total hours of use (unit: hour). This item is used for maintenance of the monitor. You
cannot reset this HOUR METER.
CONTROL LOCK
Tur ns on (or off) the control lock function to disable the buttons on the front panel.
NOTE
The following operations are available even though this function is activated.
– Turning on/off the monitor
– Displaying the set-up menu (by pressing
button while pressing button) and turning “CONTROL LOCK” to “OFF”
– Operating the monitor by an external control
If you try other operations, “ Control lock on!” appears on the screen.
all reset
Restores all the settings and adjustments of the monitor to the default.
NOTE
• “HOUR METER” and the settings done by using the adjustment knobs on the front panel will not be reset.
• After performing “all reset,” the monitor is turned off then turned on automatically.
*
1
DT-V24L1D and DT-V20L1D only
*
2
Memorized for each input.
Using “CHARACTER SET.”
Enter a name for an input video source following the steps below.
1 Select “CHARACTER SET.”
2 Press buttons to select the first character.
• Each time you press button, the character changes as follows. Press button to reverse the order.
3 Press button to move the arrow to the next.
4 Repeat steps 2 and 3 (10 characters at maximum).
5 Press MENU button to store the source name.
Technical information
Space
(☞ “External Control” on pages 14 and 15)
Setting value: OFF, ON
DT-V2420L1D_UA_R.indd 13DT-V2420L1D_UA_R.indd 13 06.11.17 10:40:21 AM06.11.17 10:40:21 AM