JVC DT-V20L1 Computer Monitor User Manual


 
7
1 Display the menu.
To display the main menu
\ Press MENU button.
To display the set-up menu
\ Press button while pressing button.
2 Press buttons to select an item,
then press button.
3 Press buttons to select an item,
then press buttons to make
adjustments.
4 Press MENU button to return to the
previous menu.
Pressing the button again finishes the menu
operation.
NOTE
For some items, adjustments will be made by pressing
in step 2 .
Menu Operations
Select audio channels of EMBEDDED AUDIO
signals to output from the speakers (L/R) and
MONITOR OUT (L/R) terminals.
1 Press or button to display the
screen for audio channel selection.
You cannot display this screen when displaying
a menu screen.
2 Press buttons to select the left
(L) or right (R).
3 Press buttons to select an
audio channel.
NOTE
• You can select channels from 12 audio channels.
• You have to choose a group of selectable audio
channels before the channel selection ( “E.AUDIO
GROUP” on page 11).
4 Press MENU button to finish the
audio channel selection.
Audio Channel Selection
(DT-V24L1D and DT-V20L1D only)
About the Status Display
When the main menu is displayed
When the set-up menu is displayed
Selected item
Selected item
Operation guide
Operation guide
Ex.: When “AREA MARKER” is selected
Selected item
The monitor displays the status information below
depending on the settings of the menu and buttons at
the top of the screen.
1 Audio level meter*
• Not displayed when no EMBEDDED AUDIO
signal is input or “LEVEL METER ch” is set to
“OFF” ( “AUDIO SETTING” on page 11).
2 Signal format
• “
*
is displayed at the end of the indication when
a DVI-D signal protected with HDCP is input.
• “NO SYNC” is displayed when no video signal is
input.
• “Out of range” is displayed for a noncompliant
video signal input. When “COLOR SYSTEM” is
set to “AUTO” ( “OTHER SETTING” on page
11) and the noncompliant video signal is a
composite one, “OTHERS” is displayed.
3 Setting of “COLOR TEMP.”
“WHITE BALANCE SET.” on page 12
• “
*
is displayed at the end of the indication when
“9300K” or “6500K” is selected in “COLOR
TEMP.” and its drive levels or cutoff points are
adjusted.
4 Displayed when “SYNC INPUT SEL.” is set to
“EXT.” (external synchronization)
“ SYNC FUNCTION” on page 11
5 Source name entered in “CHARACTER SET.”
“INFORMATION” on page 13
• Displayed when “MONITOR NAME” is set to
“ON” ( “INFORMATION” on page 13).
• Displayed in large letters when “STATUS
DISPLAY” is set to “OFF” or “AUTO” (
“INFORMATION” on page 13).
6 Time code*
u T.C. (time code) button/lamp” on page 6
• When the input signal includes no time code,
“TC:– –:– –:– –:– –is displayed.
7 CRC error indication*
“CRC ERROR” in “INFORMATION” on page 13
• A red square is displayed when an error occurs.
* DT-V24L1D and DT-V20L1D only
If you press INPUT SELECT button of the current
input, the information below (24 and 8) is
displayed in large letters for about three seconds.
Then the status information on the left column
(17) is displayed.
When “STATUS DISPLAY” is set to “AUTO” or “ON,”
the information below is also displayed in the cases
below ( “INFORMATION” on page 13).
• When you change the input
• When the signal condition of the current input
changes
• When turn on the monitor
8 Setting of “COMPO./RGB SEL.” or the signal
form of DVI input
“COMPO./RGB SEL.” or “DVI INPUT SEL.” on
page 10
NOTE
When “STATUS DISPLAY” is set to “OFF” or “AUTO” (
“INFORMATION” on page 13), 24 are not displayed at
the top of the screen.
While displaying any of the status indications except 6 at
the top of the screen, the picture is displayed below the
status display area. (The status display may overlap with
the picture when a computer signal is input.)
DT-V2420L1D_UA_R.indd 7DT-V2420L1D_UA_R.indd 7 06.11.17 10:40:15 AM06.11.17 10:40:15 AM