Filter
Top Products
6
Daily Operations / Connections
7 Front panel
q SCREENS CHECK button/lamp
Displays only the selected element (R, G, or B) of
the video signal.
• Each time you press this button, the picture
changes in the following order.
w ASPECT button/lamp
Changes the aspect ratio of the picture from 4:3
to 16:9 when the picture of 16:9 aspect ratio is
squeezed into 4:3 format signal.
• To return to 4:3, press the button again.
• This function does not work when displaying the
picture in the 1:1 mode.
e SCOPE button/lamp
Displays/hides the indication of the wave form
monitor and vector scope. (☞ “SCOPE SETTING”
on page 15)
• Each time you press this button, the window
changes in the following order.
r T.C. (time code) button/lamp
Activates/deactivates the display of the time data
(time code) contained in the SDI signal.
(☞ “On the Information Display” on page 7)
• Select the time code type in “TIME CODE” of
SET-UP MENU (☞ page 18).
t INPUT SELECT buttons/lamps
Selects an input.
SDI 1: E. AUDIO HD/SD SDI (IN 1) terminal
SDI 2: E. AUDIO HD/SD SDI (IN 2) terminal
DUAL LINK SDI:
E.AUDIO HD SDI (IN 1, IN 2) terminal
DVI: DVI-D (HDCP) terminal
COMPO.: COMPO. terminal
VIDEO: VIDEO terminal
• The lamp for the selected input lights.
• When “SDI DUAL LINK” is set to “ON” in MAIN
MENU, press SDI 1 or SDI 2 to select DUAL LINK
(☞ page 12).
y Power lamp
Unlit: The monitor is completely off (both the
POWER switch and DC switch on the rear panel
are turned off).
Lights in Green: The monitor is on.
Lights in orange: The monitor is off (on standby).
Flashes in orange: The monitor is in the P. SAVE
(power save) mode. (☞ “NO SYNC ACTION” in
“SYNC FUNCTION” on page 15)
u button
Turns on and off (on standby) the monitor.
• The power switches (the POWER switch and DC
switch) are equipped on the rear panel of the
monitor (☞ 9 on page 8, w on page 9).
• To turn off the monitor completely, turn off the
POWER switch and DC switch.
i DC lamp
When the DC 12 V power voltage is being lowered
due to the battery consumption, the lamp changes
to orange from green. When the voltage becomes
lower than a certain level, the monitor automatically
turns off and the lamp turns to red.
• Make sure to turn off the POWER switch and
DC switch on the rear panel before replacing the
battery.
• The length of time that the lamp lights in orange
differs depending on the type of battery or the
battery condition. It is recommended to replace
the battery when the lamp turns to orange.
Tally lamp
This lamp is controlled by the tally function of the
MAKE/TRIGGER terminal.
• You can select the color of the tally lamp from
“
GREEN” or “RED.” (☞ “TALLY SELECT” in
“FUNCTION SETTING” on page 16 and “External
Control” on page 20)
• “NO EFFECT” is displayed when you press a button which is not available for the current input or signal format (the lamp lights even when the function does not
actually work).
• The items controlled by the MAKE system cannot be controlled by the buttons on the front panel (“REMOTE ON” is displayed and the lamps do not light).
5 / / / buttons
When a menu screen is displayed
Selects or adjusts menu items. (☞
“Menu
Operations” on page 7)
When no menu screen is displayed
Selects the audio channels of EMBEDDED AUDIO
signals. (☞ “Audio Channel Selection” on page 7)
•
Pressing button while holding button displays the
SET-UP MENU. (
☞
“Menu Operations” on page 7)
6 MENU button
Activates/deactivates the display of the MAIN MENU.
(☞ “Menu Operations” on page 7)
7 COLOR OFF button/lamp
Displays only the luminance signal.
• This function does not work for RGB input signals.
8 1:1 button/lamp
Displays the picture in the original resolution of the
input signal.
• The aspect ratio of the picture may change
depending on the input signal.
9 AREA MARKER button/lamp
Displays/hides the area marker.
• Select the style of the area marker in “MARKER”
of the MAIN MENU (☞ page 13).
• This function works only when displaying the
picture in 16:9 aspect ratio.
• This function does not work when “AREA
MARKER” or “R-AREA MARKER” is set to “OFF”
in “MARKER.”
p SAFETY MARKER button/lamp
Displays/hides the safety marker.
• Adjust the area of the safety marker in “MARKER”
of MAIN MENU (☞ page 13).
• This function does not work when displaying the
picture in the 1:1 mode.
• This function does not work when “SAFETY
MARKER” or “R-SAFETY MARKER” is set to
“OFF” in “MARKER.”
1 Speakers (stereo)
The speakers emit the same audio signal emitted
from the AUDIO (MONITOR OUT) terminals.
(☞ “ 5 AUDIO (MONITOR OUT) terminals” on
page 8)
2 VOLUME adjustment knob
Adjusts the volume.
3 Picture adjustment knob
PHASE: Adjusts the picture hue.
CHROMA: Adjusts the picture color density.
BRIGHT: Adjusts the picture brightness.
CONTRAST: Adjusts the picture contrast.
• PHASE and CHROMA cannot be adjusted for
certain signal formats.
• When “COMPONENT PHASE” is set to
“DISABLE” and an NTSC signal is input, PHASE
can be adjusted (☞ page 16).
4 MUTING button
Turns off the sound when no menu screen is
displayed.
• To cancel the function, press the button again or
turn the VOLUME adjustment knob.
• Muting function is also canceled when
“BALANCE” of “AUDIO SETTING” in the MAIN
MENU is changed (☞ page 14).
RGB (Normal screen) Red screen
Green screenBlue screen
Vector scope
No display Wave form monitor
DT-V17G1_EN.indd 6DT-V17G1_EN.indd 6 09.12.3 7:55:13 PM09.12.3 7:55:13 PM