Filter
Top Products
12
First Time Installation
When you turn on the power and the monitor, “First Time Installation” appears.
Start setting referring to the menu configuration.
For the setting items, see the pages below.
“Language” • ☞ “Language” on page 20
“No Sync Action” • ☞ “Sync Function” on page 18
“No Operation Action” • ☞ “No Operation Action” on page 18
Setting procedure
1 Press
to move the cursor to the setting item
2 Press
to select the setting values
● Each time you press one of these buttons, the setting value changes.
3 Move the cursor to “Set”
4 Press to finish setting
● When you change the settings, a confirmation message appears.
Operate according to directions.
The operation procedure
1 Press the MENU button to display the Main Menu
To display the Main Menu
➡ Press the MENU button.
To display the Set-Up Menu
➡ Press the button while holding the button.
2 Use the buttons to select an item and press the button to
proceed to the next screen
3 Use the buttons to select an item and press the button to
proceed to the next screen
● For some items, pressing the buttons adjusts the setting.
4 Use the buttons to select an item and use the buttons
to adjust the setting
5 Press the MENU button to finish operations
● Press the MENU button repeatedly until the menu screen disappears.
On the Status Display
If you press the INPUT SELECT button (☞ 9 on page 10) currently lit, the status of the input signal and setting of MUTING are displayed for about
3 seconds.
● Make the setting to display/hide the status in “Status Display” of the “Information”. (☞ page 20)
● When “Status Display” is set to “Auto” or “On,” the status below is also displayed in the following cases:
– When you change the input
– When the signal condition of the current input changes
– When you turn on the monitor
● When “Status Display” is set to “On,” the signal format will remain displayed 3 seconds after the status is
displayed.
1 Signal format
● For the contents displayed, see “Available signals” on page 30 and “On the signal format” below.
On the signal format
The following messages appear depending on the type of input signals and their conditions.
When a HDMI signal protected with HDCP is input
When no video signal comes in
When a noncompliant video signal comes in
“*” (at the end of the indication) ➔
“No Sync” ➔
“Out of range” ➔
2 Signal format of HDMI and VIDEO/COMPONENT input
3 Setting of “MUTING”
• Only appears when in mute mode. (☞ 5 on page 10).
Showing Input Signals (cont.)
Main Menu
Selected item
Operation guide
Set-Up Menu
Ex.: When “Picture Function”
in the Main Menu is selected
Menu Configuration
● The menu screen disappears automatically if no operations are
made for about 30 seconds.
● Inoperable menus will be grayed out.
● Some items will not be displayed on the menu depending on the
selected input and signal format.
(KTUV6KOG+PUVCNNCVKQP
1HH
'PINKUJ
1HH
.CPIWCIG
0Q5[PE#EVKQP
0Q1RGTCVKQP#EVKQP
5GV
● Once the settings have been adjusted, this screen will not appear
again.
● The settings can be changed afterwards in Main Menu and Set-Up
Menu.
/CKP/GPW
2KEVWTG(WPEVKQP
5K\G2QUKVKQP#FLWUV
#URGEV
5KIPCN5GVVKPI
/CTMGT
#WFKQ5GVVKPI
5EQRG5GVVKPI
0Q1RGTCVKQP#EVKQP
1HH
5[PE(WPEVKQP
&[PCOKE
6HW8S0HQX
)XQFWLRQ6HWWLQJ
$OO/RFN
(QJOLVK
3LFWXUH6XE$GMXVW
:KLWH%DODQFH6HWWLQJ
5HPRWH6HWWLQJ
,QIRUPDWLRQ
&RQWURO/RFN
/DQJXDJH
,0'
DOOUHVHW
E^XijgZ;jcXi^dc
/"'%
/D[[
/%,
/CdgbVa
/=VgY
/'#'
/.(%%@
7VX`a^\]i
6eZgijgZ
6eZgijgZAZkZa
8I>
AI>
<VbbV
8dadgIZbeZgVijgZ
hjWbZcj
gZhZi
/CKP/GPW
2KEVWTG(WPEVKQP
5K\G2QUKVKQP#FLWUV
#URGEV
5KIPCN5GVVKPI
/CTMGT
#WFKQ5GVVKPI
5EQRG5GVVKPI
0Q1RGTCVKQP#EVKQP
1HH
5[PE(WPEVKQP
&[PCOKE
DT-V9L5_EN_1.indb 12DT-V9L5_EN_1.indb 12 10/10/2012 5:18:47 PM10/10/2012 5:18:47 PM