Filter
Top Products
9
Transport control on the MASTER:
The slide transport runs, as usual, via
the two transport buttons.
Transport control on the SLAVE:
The slide transport is via the two focus
buttons.
It is therefore not possible to focus the
two projectors with this setting!
Access to individual slides (RA
control) is still possible (see *Random
Access).
PARELLEL PROJECTION
(970)
You can also program parallel
projections via your remote control.
Press <970> and <*>.
Both projectors will then move to the
same slide tray setting and both lamps
are switched on.
Focussing:
MASTER: With the focus buttons.
SLAVE: First press <666> and <*>,
then use focus buttons (not possible
with models 7010 and 9010!).
With a next slide transport this
command is inactive again.
The slides are numbered from 1 - 80
(or 1 - 140 on a 140 slide tray) in this
parallel mode and can be selected as
such. If, forexample, no. 13 is selected,
both projectors will go into search
mode and project the slides in the slide
tray slot no. 13.
BACK INTO DISSOLVE MODE
(990)
By inputting this combination of
numbers and the <*> you can go back
to a basic setting for the two projector
dissolve. The dissolve time previously
set is retained.
Press <990> and <*> on your remote
control.
*SECURITY SETTING FOR
PRESENTATIONS USING IR
REMOTE CONTROL (989)
If all the
preparations for a
presentation have
been made, it is
important for a
presentation to run
“smoothly”. In
spite of the best
preparation “small
hitches” can occur if the presenter
presses the wrong button on the remote
control by accident.
With the security setting you can set up
your remote control so that when the
transport button is pressed, only one
transport step or only one dissolve is
executed. The focus buttons are also
disabled so that if you happen to press
the buttons, the focus on the projector
is not changed. All other functions
remain active (and can be secured by
the cover on the remote control). Even
novice presenters can now “not put a
foot wrong”!
This is how to put your remote control
into the security position:
Press (989) and <*>.
The following functions are changed:
• Transport forwards:
Regardless of how long you press a
button, the projector only carries out
a single transport step or the next
dissolve. In case the parallel mode is
activated the slides will only be
projected if the button is released.
• Transport backwards:
Hold down the button for atleast two
seconds. The projector carries out a
single step backwards and the slide
will be projected in the moment the
button is released.
• Focus:
Inactive
Note:
• Of course the security position can
also be used to control projection
with a single projector.
• For the individual projector control
(980) this command cannot be
applied.
To cancel the security setting:
The presentation mode can only be
cancelled by a reset command or by
switching the projectors off and on
again [see *RESET (999)].
Press (999) and <*>.
*RESET (999)
When you input this command, the two
projectors are automatically reset to
their zero position. Reset is the same as
switching the projectors off and back
on again (see also Basic setting).
Press <999> and <*> on your remote
control.
*AUTOTIMER (600...660)
A Timer function can also be set via the
IR remote control. This is particularly
relevant for the EKTAPRO 7010/7020
as this does not have a built-in timer.
Any time from 1 to 6 seconds can be
set (in steps of one second). If you
transmit such a command to the
MASTER projector, the first transport
command or the first dissolve is carried
out immediately. This is a check for
you that the projector is now in
autotimer mode.
Example
You want a dissolve to take place every
22 seconds:
➔ Press <622> and <*> on your
remote control.
The slide tray goes to position 1 and the
first picture with the dissolve time is
faded up. The first dissolve occurs after
22 seconds.
Important
Whilst the MASTER projector is
carrying out a slide transport, no
commands should be sent with the IR
remote control. This can lead to the
command not being recognized,
especially in the case of very short
autotimer times. In this case the
projector should be switched off- and
on again.
Switching the autotimer off
You can turn the autotimer off again at
any time:
Press <600> and <*> on your remote
control.