Filter
Top Products
01. Power k a 00 ~ 01
02. Input Select k b 00 ~ 04
03. Aspect Ratio k c 00 ~ 03
04. Screen Mute k d 00 ~ 01
05. Volume Mute k e 00 ~ 01
06. Volume Control k f 00 ~ 64
07. Contrast k g 00 ~ 64
08. Brightness k h 00 ~ 64
09. Color k i 00 ~ 64
10. Tint k j 00 ~ 64
11. Sharpness k k 00 ~ 64
12. OSD Select k l 00 ~ 01
13.
Remote Control Lock Mode
k m 00 ~ 01
14. PIP/DW k n 00~ 03
15. Split Zoom k p 00 ~ 99
16. PIP Position k q 00 ~ 03
17. Treble k r 00~ 64
18. Bass k s 00 ~ 64
19. Balance k t 00 ~ 64
20. Color Temperature k u 00 ~ 03
21. Red Adjustment k v 00 ~ 3C
22. Green Adjustment k w 00 ~ 3C
23. Blue Adjustment k $ 00 ~ 3C
24. SUB INPUT Source k y 00 ~ 04
25. Abnormal State k z 00 ~ 0a
26. ISM Method j p 00 ~ 03
27. Low Power j q 00 ~ 01
28. Orbiter Time Setting j r 01 ~ FE
29. Orbiter Pixel Setting j s 01 ~ 09
30. Picture Size j t 00 ~14(1E,20)
31. Auto Config j u 01
32. Send IR Code m c 00 ~ F0
(Refer to p.36)
30 Plasma Monitor
External Control Device Setup
Set ID
Set ID
- Use this function to specify a monitor ID number.
- Refer to ‘Real Data Mapping 1’. See page 31.
• Baud rate :9600 bps (UART)
• Data length : 8 bits
• Parity : None
* Use a crossed (reverse) cable.
• Stop bit : 1 bit
• Communication code : ASCII code
Communication Parameters
Communication Parameters
1. Press the MENU button and then use
D / E
button to select the SPECIAL menu.
2. Press the G button and then use
D / E
button to select Set ID.
3. Press the G button and then use F / G button to adjust Set ID to choose the
desired monitor ID number. The adjustment range of Set ID is 1 ~ 99.
4. Press the OK button to save.
Transmission
*
[Command 1]: First command to control PDP set. (j, k or m)
*
[Command 2]: Second command to control PDP set.
*
[Set ID]: You can adjust the set ID to choose desired monitor
ID number in Special menu. Adjustment range is 1
~ 99. When selecting Set ID ‘0’, every connected
PDP set is controlled. Set ID is indicated as deci-
mal (1~99) on menu and as Hexa decimal
(0x0~0x63) on transmission/receiving protocol.
*
[DATA]: To transmit command data.
Transmit ‘FF’ data to read status of command.
*
[Cr]: Carriage Return
ASCII code ‘0x0D’
*
[ ]: ASCII code ‘space (0x20)’
[Command1][Command2][ ][Set ID][ ][Data][Cr]
T
T
ransmission / Receiving Protocol
ransmission / Receiving Protocol
OK Acknowledgement
* The Monitor transmits ACK (acknowledgement) based on
this format when receiving normal data. At this time, if the
data is data read mode, it indicates present status data. If
the data is data write mode, it returns the data of the PC
computer.
[Command2][ ][Set ID][ ][OK][Data][x]
Error Acknowledgement
* The Monitor transmits ACK (acknowledgement) based on
this format when receiving abnormal data from non-viable
functions or communication errors.
[Command2][ ][Set ID][ ][NG][Data][x]
Data 1: Illegal Code
2: Not supported function
3: Wait more time
COMMAND 1 COMMAND 2 DATA
(Hexadecimal)
Command Reference List
Command Reference List
SPECIAL
Prev.
Language
Key lock
ISM Method
Low power
Set ID G
Demo
OSD Rotate
SPECIAL
Menu
1