Filter
Top Products
5
The LN9101M Anamorphic Lens System is designed
to mount together with the Marantz VP-11 onto the
ceiling of a typical room. Before choosing the location
on the ceiling, it is important to first read the “Installa-
tion” section of the VP-11 User Guide.
Some of the brackets from the Marantz MT20 (op-
tional ceiling mounting bracket) will be used to mount
the combination of the projector and LN9101M to the
ceiling. In some installations the EXT10 bracket will
also be used (optional extension pole kit).
This installation guide includes the assembly
instuctions from the MT20 and EXT10 Installation
Guides for easier installation. The LN9101M/MT20/
EXT10 were designed and manufactured to meet
strict quality and safety standards. There are however,
some installation and operation precautions which
you should be particularly aware of:
1. Read instructions - All the safety and operating
instructions should be read before the products are
used.
2. Retain instructions - The safety and operating in-
structions should be retained for future reference.
3. Heed warnings - All warnings on the products and
in the instructions should be adhered to.
4. Follow instructions - All installation instructions
should be followed.
5. Use only the parts provided with the mount, along
with any parts (commercially available) that are
specified in these instructions.
6. Do not modify the mount or the parts provided with
the MT20/EXT10/LN9101M.
7. Do not use damaged parts. If any parts become
damaged, contact your Marantz Dealer or Marantz.
8. All bolts and screws must be tightened securely
when instructed to do so.
9. After the projector mounting plate is attached to
Dimensions
The following dimensions can assist in determining
the best
location
for the
combi-
nation
of the
Marantz
VP-11
and the
LN9101M
Ana-
morphic
Lens System.
Installation Overview
the projector make sure not to block any additional
ventilation openings.
10. Special techniques and experience are required
when installing the projector with the MT20/
EXT10/LN9101M. Contact your Marantz Dealer to
install the projector for you.
11. Once the projector is installed, periodic safety
checks of the rigidity of the MT20 Mounting Brack-
ets, EXT10 Extension Pole, LN9101M Anamorphic
Lens System and the VP-11 to the ceiling along
with secure fastening of all hardware should be
conducted on a regular basis.
EXT10 Assembly
After reading the “Installation” Section of the VP-11
User Guide and it has been determined the EXT10
Extension Pole will be needed to meet the require-
ments of location and ventilation for the Projector,
assemble the EXT10 by performing the steps below.
If the EXT10 will not be needed, proceed to the MT20
Assembly on page 7.
Note: The EXT10 hardware, fasteners and parts list
are located in a separate shipping carton from the
projector.
1. The EXT10 is adjustable from 43-3/4 inches to 24
inches as supplied. If the default range is accept
-
able proceed to Step 3. The adjustable range may
be changed to 24 inches to 14-5/8 inches by cut-
ting both poles. When the installation requires the
24 inches to 14-5/8 inches range proceed to Step
2.
2. Cut the Outside
Pole to 13-3/8
inches from the
end the mount-
ing plate will be
attached. Cut
the Inside Pole
to 13-3/4 inches
from the end the
mounting plate
will be attached.
Refer to figure 1.
3. Attach the Bottom Mount-
ing Plate (the flange with
the wider space) to the
Outside Pole with two
Round Head Philips 1/4-20
x 3/8 Screws. In a similar
manner, attach the remain-
ing Plate to the Inside Pole. Refer to figure 2.
4. Assemble the Pole Pieces together making sure
to orient them as illustrated in figure 3 on the next
page.
Cut Here
Cut Here
Outside
Pole
Inside
Pole
13-3/8”
13-3/4”
Figure 1
Figure 2
21-15/16"
55.7cm
9-13/16"
24.9cm
22-1/2"
57.2cm