Mitsubishi Electronics SD110 Projector User Manual


 
EN-4
Important safeguards
Please read all these instructions regarding your projector and
retain them for future reference. Follow all warnings and
instructions marked on the projector.
1. Read instructions
All the safety and operating instructions should be read
before the appliance is operated.
2. Retain instructions
The safety and operating instructions should be retained
for future reference.
3. Warnings
All warnings on the appliance and in the operating instruc-
tions should be adhered to.
4. Instructions
All operating instructions must be followed.
5. Cleaning
Unplug this projector from the wall outlet before cleaning
it. Do not use liquid aerosol cleaners. Use a damp soft
cloth for cleaning.
6. Attachments and equipment
Never add any attachments and/or equipment without the
approval of the manufacturer as such additions may result
in the risk of fire, electric shock or other personal injury.
7. Water and moisture
Do not use this projector near water or in contact with
water.
8. Accessories
Do not place this projector on an unstable cart, stand, tri-
pod, bracket or table. Use only with a cart, stand, tripod
bracket, or table recommended by the manufacturer or
sold with the projector. Any mounting of the appliance
should follow the manufacturer’s instructions and should
use a mounting accessory recommended by the manufac-
turer.
An appliance and cart combination should be moved with
care. Quick stops, excessive force and uneven surfaces
may cause the appliance and cart combination to over-
turn.
9. Ventilation
Slots and openings in the cabinet are provided for ventila-
tion, ensuring reliable operation of the projector and to
protect it from overheating. Do not block these openings or
allow them to be blocked by placing the projector on a bed,
sofa, rug, or bookcase. Ensure that there is adequate ven-
tilation and that the manufacturer’s instructions have been
adhered to.
10. Power sources
This projector should be operated only from the type of
power source indicated on the marking label. If you are not
sure of the type of power, please consult your appliance
dealer or local power company.
11. Power-cord protection
Power-supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or
against them. Pay particular attention to cords at plugs,
convenience receptacles, and points where they exit from
the appliance. Do not put the power cord under a carpet.
12. Overloading
Do not overload wall outlets and extension cords as this
can result in a fire or electric shock.
13. Objects and liquids
Never push objects of any kind through openings of this
projector as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the projector.
14. Servicing
Do not attempt to service this projector yourself. Refer all
servicing to qualified service personnel.
15. Damage requiring service
Unplug this projector from the wall outlet and refer servic-
ing to qualified service personnel under the following con-
ditions:
(a) If the power-supply cord or plug is damaged.
(b) If liquid has been spilled, or objects have fallen into the
projector.
(c) If the projector does not operate normally after you fol-
low the operating instructions. Adjust only those con-
trols that are covered by the operating instructions. An
improper adjustment of other controls may result in
damage and may often require extensive work by a
qualified technician to restore the projector to its nor-
mal operation.
(d) If the projector has been exposed to rain or water.
(e) If the projector has been dropped or the cabinet has
been damaged.
(f) If the projector exhibits a distinct change in perfor-
mance - this indicates a need for service.
16. Replacement parts
When replacement parts are required, be sure that the
service technician has used replacement parts specified
by the manufacturer or parts having the same characteris-
tics as the original part. Unauthorized substitutions may
result in fire, electric shock or other hazards.
17. Safety check
Upon completion of any service or repair to this projector,
ask the service technician to perform safety checks deter-
mining that the projector is in a safe operating condition.