Mitsubishi Electronics XD400U Projector Accessories User Manual


 
EN - 5
ENGLISH
WARNING:
Unplug immediately if there is something wrong with
your projector.
Do not operate if smoke, strange noise or odor comes
out of your projector. It may cause fi re or electric shock.
In this case, unplug immediately and contact your
dealer.
Never remove the cabinet.
This projector contains high voltage circuitry. An inad-
vertent contact may result in an electric shock. Except
as specifi cally explained in User Manual, do not attempt
to service this product by yourself. Please contact your
dealer when you want to fi x, adjust, or inspect the pro-
jector.
Do not modify the projector.
It can lead to fi re or electric shock.
Do not keep using the damaged projector.
If the projector is dropped and the cabinet is damaged,
unplug the projector and contact your dealer for inspec-
tion. It may lead to fi re if you keep using the damaged
projector.
Do not face the projection lens to the sun.
It can lead to fi re.
Use correct voltage.
If you use incorrect voltage, it can lead to fi re.
Do not place the projector on uneven surface.
Place the projector on a level and stable surface only.
Do not look into the lens when the projector is oper-
ating.
It may hurt your eyes. Never let children look into the
lens when the projector is on.
Do not unplug the power cord during operation.
It can lead to lamp breakage, fi re, electric shock or
other trouble. Wait for the fan to stop before unplugging
the power cord.
Do not touch the air outlet grilles and bottom plate.
Do not touch them or put other equipment close to the
air outlet grilles because they become hot during opera-
tion. The heated air outlet grilles and bottom plate may
cause injury or damage to other equipment. Also, do
not put the projector on a desk that is easily affected by
heat.
Do not look into the air outlet grilles when projector
is operating.
Heat, dust, etc. may blow out of them and hurt your
eyes.
Do not block the air inlet and outlet grilles.
If they are blocked, heat may be generated inside the
projector, causing deterioration in the projector quality
and fi re.
Place of installation
For safety's sake, do not use the projector at any place
subjected to high temperature and high humidity.
Please maintain an operating temperature, humidity,
and altitude as specifi ed below.
Operating temperature: between +41˚F (+5˚C) and
+95˚F (+35˚C)
Operating humidity: between 30% and 90%
Never put any heat-producing device under the
projector to prevent the projector from being over-
heated.
Do not install the projector at a place that is unstable
or subject to vibration.
Do not install the projector near any equipment that
produces a strong magnetic fi eld. Also refrain from
installing the projector near any cable carrying a
large amount of current.
Place the projector on a solid, vibration-free surface.
Otherwise it may fall, causing serious injury or dam-
age.
Do not stand the projector on its end. It may fall,
causing serious injury or damage.
Slanting the projector more than ±10˚ (right and left)
or ±15˚ (front and rear) may cause trouble or explo-
sion of the lamp.
Do not place the projector near air-conditioning unit
or heater to avoid the air outlet and inlet grilles from
being exposed to hot air.
COMPLIANCE NOTICE OF FCC
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced Radio / TV technician for help.
Changes or modifi cations not expressly approved by Mitsubishi could void the user's authority to operate this equip-
ment.
COMPLIANCE NOTICE OF INDUSTRY CANADA
This Class B digital apparatus complies with Canadian ICES-003.