Filter
Top Products
EN-6
(f) If the projector exhibits a distinct change in
performance - this indicates a need for ser-
vice.
16. Replacement parts
When replacement parts are required, be sure
that the service technician has used replace-
ment parts specified by the manufacturer or
parts having the same characteristics as the
original part. Unauthorized substitutions may
result in fire, electric shock or other hazards.
17. Safety check
Upon completion of any service or repair to this
projector, ask the service technician to perform
safety checks determining that the projector is
in a safe operating condition.
WARNING:
Unplug immediately if there is something
wrong with your projector.
Do not operate if smoke, strange noise or odor
comes out of your projector. It may cause fire or elec-
tric shock. In this case, unplug immediately and con-
tact your dealer.
Never remove the cabinet.
This projector contains high voltage circuitry. An
inadvertent contact may result in an electric shock.
Except as specifically explained in User Manual, do
not attempt to service this product by yourself.
Please contact your dealer when you want to fix,
adjust, or inspect the projector.
Do not modify the projector.
It can lead to fire or electric shock.
Do not keep using the damaged projector.
If the projector is dropped and the cabinet is dam-
aged, unplug the projector and contact your dealer
for inspection. It may lead to fire if you keep using the
damaged projector.
Do not face the projection lens to the sun.
It can lead to fire.
Use correct voltage.
If you use incorrect voltage, it can lead to fire.
Do not place the projector on uneven sur-
face.
Place the projector on a level and stable surface only.
Do not look into the lens when the projec-
tor is operating.
It may hurt your eyes. Never let children look into the
lens when the projector is on.
Do not unplug the power cord during oper-
ation.
It can lead to lamp breakage, fire, electric shock or
other trouble. Wait for the fan to stop before unplug-
ging the power cord. Do not touch the air outlet
grilles and bottom plate.
Do not touch them or put other equipment close to
the air outlet grilles because they become hot during
operation. The heated air outlet grilles and bottom
plate may cause injury or damage to other equip-
ment. Also, do not put the projector on a desk that is
easily affected by heat.
Do not look into the air outlet grilles when
projector is operating.
Heat, dust, etc. may blow out of them and hurt your
eyes.
Do not block the air inlet and outlet grilles.
If they are blocked, heat may be generated inside the
projector, causing deterioration in the projector qual-
ity and fire.
Do not use flammable solvents (benzene,
thinner, etc.) and flammable aerosols near
the projector.
Flammable substances may ignite causing fire or
breakdown because the temperature inside the pro-
jector rises very high while the lamp is illuminating.
Place of installation
For safety’s sake, do not use the projector at any
place subjected to high temperature and high humid-
ity. Please maintain an operating temperature,
humidity, and altitude as specified below.
• Operating temperature: between +41°F (+5°C)
and +95°F (+35°C)
• Operating humidity: between 30% and 90%
• Never put any heat-producing device under the
projector to prevent the projector from being
overheated.
• Do not install the projector at a place that is
unstable or subject to vibration.
• Do not install the projector near any equipment
that produces a strong magnetic field. Also
refrain from installing the projector near any
cable carrying a large amount of current.
• Place the projector on a solid, vibration-free sur-
face. Otherwise it may fall, causing serious injury
or damage.
• Do not stand the projector on its end. It may fall,
causing serious injury or damage.
• Slanting the projector more than ±10° (right and
left) or ±15° (front and rear) may cause trouble or
explosion of the lamp.
• Do not place the projector near air-conditioning
unit or heater to avoid the air outlet and inlet
grilles from being exposed to hot air.