Filter
Top Products
ENGLISH-15
Preparation
14-ENGLISH
BThe wireless remote control and the projector itself have the same control
buttons available.
#RGB INPUT indicator
(page 17)
This indicator shows whether a
signal is being input to the RGB
input connectors (RGB 1
IN/RGB2 IN). When an input
signal is detected, the indicator
illuminates.
$LAMP indicator
(page 42)
This indicator illuminates when it
is time to replace the lamp unit. It
flashes if a circuit abnormality is
detected.
%TEMP indicator
(page 42)
This indicator illuminates if an
abnormally high temperature is
detected inside the projector or
around it. If the temperature rises
above a certain level, the power
supply will be turned off
automatically and the indicator
will illuminate or flash.
&POWER button
(pages 24 and 25)
'Power indicator
(pages 24 and 25)
This indicator illuminates red
when the MAIN POWER switch is
turned on (standby mode), and
illuminates green when the power
is turned on and a picture starts
to be projected.
(AUTO SETUP button
(pages 17 and 25)
If this button is pressed while a
picture is being projected, the
projection settings will be
adjusted automatically in
accordance with the signal being
input. In addition, the angle of tilt
of the projector will be
automatically detected and
adjusted in order to correct any
keystone distortion. (“AUTO
SETUP” will appear on the
screen during adjustment.) Set
“AUTO KEYSTN” in the
OPTION1 menu to “OFF” to
prevent any deterioration of the
picture as a result of keystone
correction.
<Projector control panel and remote control unit>
ENTER
FREEZE
SHUTTER
INDEX
WINDOW
PROJECTOR
VOLUME D.ZOOM
STD
AUTO
SETUP
VIDEO
INPUT
POWER
RGB
MENU
TEMP
LAMP
RGB INPUT
INPUTAUTO SETUP
POWER
STANDBY(R)
ON(G)
MENU ENTER
&
(
+
-
.
& ( )
% '$#
, + *
/
0
1
2
,
)
*
)Input select (INPUT, RGB,
VIDEO) buttons
(page 24)
*ENTER button
(page 28)
This button is used to accept and
to activate items selected in the
on-screen menus.
+Arrow (
FF
,
GG
,
II
and
HH
)
buttons
(page 28)
These buttons are used to select
and adjust items in the on-screen
menus.
,MENU button
(pages 26 and 28)
This button is used to display
menu screens. When a menu
screen is being displayed, it can
be used to return to a previous
screen or to clear the screen.
-FREEZE button
(page 29)
This button is used to
momentarily freeze the image so
that a still picture is displayed.
.VOLUME +/- buttons
These buttons are used to adjust
the volume of the sound output
by the projector’s built-in
speakers. Refer to page 26 for
details on how to adjust the
volume using the buttons on the
projector control panel.
/INDEX WINDOW button
(page 39)
This button can be used to split
the image projection area into a
still image and a moving image.
0D.ZOOM +/- buttons
(page 30)
These buttons are used to
enlarge certain portions of the
projected image.
1STD (standard) button
(page 29)
This button is used to reset the
projector adjustment values to the
factory default settings.
2SHUTTER button
(page 38)
This button is used to
momentarily turn off the picture
and sound.
Storing the card
remote control unit
#Turn off the MAIN POWER
switch and disconnect the
power cord plug from the wall
outlet. (Refer to page 25.)
$Gently turn the projector
upside down.
%Open the card remote control
unit holder.
&Place the card remote control
unit inside.
'Close the card remote control
unit holder.
AU
T