Filter
Top Products
30
Troubleshooting
Reinstalling Software
Before Reinstallation
1
Turn off the computer and insert the CD/DVD drive into
the multimedia pocket. (
“Multimedia Pocket”)
2
Turn on the computer, and press F2 while [Panasonic]
boot screen is displayed.
The Setup Utility will start up.
If the password has been set, enter the Supervisor Pass-
word.
3
Write down all of the contents of the Setup Utility and
then press F9 .
At the confirmation message, select [Yes] and press
Enter .
4
Select [Boot] menu, then select [IDE MP: xxxxxxxxxx]
and press F6 until [IDE MP: xxxxxxxxxx] is at the top
of the [Boot] menu.
5
Place the Product Recovery DVD-ROM into the CD/DVD
drive.
6
Press F10 .
At the confirmation message, select [Yes] and press
Enter .
The computer will restart, and this screen should appear.
Reinstalling
Preparing
You will need the Product Recovery DVD-ROM and CD/DVD drive (included).
Important
Before the reinstallation procedure, remove all peripherals (except for the CD/DVD drive).
Be sure the AC adaptor is connected until the reinstallation procedure is completed.
Even if reinstallation is executed, the number of times that the DVD video region code can be set will not be returned to
the state set at the time of factory shipment. (
“DVD-ROM & CD-R/RW Drive”)
When reinstallation procedure is performed, the contents of the hard disk will be erased. Be sure to back up any critical data on
your hard disk to another media or to an external hard disk before running the reinstallation procedure.
The reinstallation procedure will return the computer to its original condition.
Even if a hard disk backup area has been created, this backup area will be erased, and all the backed up data will be lost.
(This is not the case when Windows is reinstalled in the first partition.)
• If you have created partitions for data, the data may be erased or become corrupt as a result of the reinstallation procedure.
---------------------------------------------------------------------
Select a number
---------------------------------------------------------------------
1. [ Recovery ] Reinstall Windows.
2. [ Erase HDD] Erase the whole data on HDD for security.
3. [ Backup ] Enable the Backup function.*
1
0. [ Cancel ] Cancel.
---------------------------------------------------------------------
<When the hard disk backup function has been enabled>
When the following message appears, press Y .
*
1
This is not displayed when the hard disk backup function
has been enabled.
7
Press 1 to execute [1.[Recovery]].
(You can cancel this operation by pressing 0 .)
The License Agreement screen should appear.
---------------------------------------------------------------------
Reinstalling : Windows(R) XP Professional
The Backup function has been enabled.
If [ Recovery ] or [ Erase HDD] is executed, the Backup function will be
disabled, and your Backup data will be lost.
(If Windows is reinstalled to the first partition, Backup data will not be
lost.)
Will you continue?
---------------------------------------------------------------------
8
Press 1 to select [1. Yes, I agree to the provisions above
and wish to continue!].
This screen should appear.
9
Make a selection from the menu.
When selecting [2], enter the basic partition size for the
operating system installation and press Enter .
(The data partition size is the remainder after subtract-
ing the basic partition size.)
To select [3], the initial partition size must be 6 GB or
more of the hard disk size. Reinstallation cannot be per-
formed with a small partition size.
<When the hard disk backup function has been enabled>
If you select [1] or [2], the following message appears.
In this case, press Y .
NOTE
When [2] is selected, the hard disk backup function
cannot be enabled. When using the hard disk backup
function, select [1] to reinstall Windows to the hard
disk, and then divide the hard disk into partitions
when a backup area is created (
page 36).
---------------------------------------------------------------------
Select a number
---------------------------------------------------------------------
Reinstalling : Windows(R) XP Professional
1. Reinstall Windows to the whole HDD to factory default.
2. Make two partitions, for the operating system and data. And reinstall
Windows to the operating system partition.
(All existing partitions on HDD will be lost.)
3. Reinstall Windows to the first partition.
0. Cancel
---------------------------------------------------------------------
---------------------------------------------------------------------
The Backup function has been enabled.
If [Recovery] is executed, the Backup function will be disabled, and your
Backup data will be lost.
Will you continue?
---------------------------------------------------------------------