Filter
Top Products
42 Philips · Laserfax 5120 · 5125 · 5135
EN
10 Telephone Lines and Additional Devices
Selecting the Dialling Proc-
ess
Function is not supported in all countries and n etworks
(Function is not supported in all countries and
networks)
In some countries you can set the dialling mode to pulse
dialling or tone dialling (DTMF tones).
Selecting the Dialling Process
1 Press OK, 053 and OK.
2 Use [ to select the desired dialling process.
3 Confirm with OK.
Set up the Public Switch Tel-
ephone Network (PSTN)
Function is not supported in all countries and n etworks
(Function is not supported in all countries and
networks)
Public Switch Telephone Network (PSTN)
Set up the Public Switch Telephone Network (PSTN)
Your device is automatically adjusted to the telephone net-
work if you set the country correctly (see also chapter
Selecting the Country, page 36). It is possible that further
settings are required for the Public Switched Telephone
Network (PSTN). Ask your retailer or the technical cus-
tomer service department.
1 Press OK, 032 and OK.
2 Select the desired setting using [.
3 Confirm with OK.
Set up Private Branch
Exchange (PABX)
PABX Systems
Private branch exchanges (PABX) are typical in many
offices and some households. You must dial an outside line
access code in order to get a connection to the public tele-
phone network (PSTN) from a PABX.
Additional Telephone No Extension
Set up Private Branch Exchange (PABX )
You can set up your device for operation on an extension,
indicate the length of the internal numbers (direct dial
number) and save the code which must be selected in order
to reach the Public Switched Telephone Network (PSTN)
(= outside line access code).
Outside Line Access Code is Automaticall y Dialled
Set the connection type
1 Press OK, 051 and OK.
2 Use [ to set whether you operate your device on an
extension.
3 Confirm with OK.
Set the outside line access code
Enter the length of the direct dial number
1 Press OK, 0521 and OK.
2 Enter the appropriate length for internal numbers. Use
C to delete individual characters. Assume the longest
internal number, then add one digit to that. If your
direct dial numbers consist of four digits, then you
should input5.
3 Confirm with OK.
Enter the outside line access code
1 Press OK, 0522 and OK.
2 Enter the outside line access code with which you reach
the public telephone network. This is usually 0.
3 Confirm with OK.
Notice
Selecting the Dialling Process
Only use pulse dialling if tone dialling is not yet
activated for your telephone line.
Notice
Public Switch Telephone Network
(PSTN)
You can use this function to set your device to
connect to the Public Switch Telephone Net-
work (PSTN). To connect to a Private Branch
Exchange (PABX) see also chapter on set up Pri-
vate Branch Exchange (PABX) , page 42.
Notice
Additional Telephone No Extension
An additional telephone connected to the device
on a telephone socket is not considered an exten-
sion.
Notice
Outside Line Access Code is Automati-
cally Dialled
Once these settings are in place, you will no longer
need to prefix the outside line access code every
time you enter an external number. The device will
automatically add the outside line access code in
front of numbers that are the same length or longer
than the configured direct dial numbers.
Notice
Incorrect Outside Line Access Code
In rare cases, the outside line access code may be
a different number or a two-digit number. For
older telephone systems, the outside line access
code can be R (= Flash). Press
Rø
to enter this
outside line access code. If the connection to the
public telephone network is not possible, con-
tact your telephone system supplier.
lpf-5120-5125-5135-manual-uk-int-253117544-b.book Seite 42 Mittwoch, 16. Dezember 2009 10:01 10