Filter
Top Products
195
Settings Common to All Modes (System Function)
Settings Common to All Modes (System Function)
Sampling
Default File Type
Specifies the file format used when saving a sample.
Value:
WAV, AIFF
Pre Sample Time
0–1000 ms
Value:
OFF, ON
The length of sound preceding the moment at which sampling was
manually or automatically initiated that will be captured in the
sample. This lets you prevent the attack portion of the sound from
being omitted from the sample.
Trigger Level
Volume level at which sampling will begin when Auto Trig is ON
A setting of 0 is the minimum.
Value:
0–7
Gap Time
Length of silence at which the sample will be divided
Whenever there is a silent region longer than the specified time, the
sample will be divided at that point, and the next sample number
will be assigned to the sound that follows. This parameter is valid
only when you are using Auto Divide Sampling.
Value:
500, 1000, 1500, 2000 ms
External Source Select
Input source of the external input sound
Value
LINE-L-R:
INPUT jacks L/R (stereo)
LINE-L:
INPUT jack L (mono)
MIC:
INPUT jack (mono, mic level)
Trimming Switch
If this is turned on, the Start point and End point settings will be
automatically adjusted after sampling is performed, so any silent
portions at the beginning or end of the sampled sound are excluded.
Value:
OFF, ON
Skip Back Time
Specifies how much earlier in time that you want sampling to take
place when you use Skip Back Sampling. If “OFF” selected, skip-
back sampling cannot be performed.
Value:
OFF, 5s–40s
Start up
Preset Default Load
Specifies whether the preset samples will be loaded into memory at
power-on (ON) or not (OFF).
Value:
OFF, ON
Sample Default Load
Specifies whether the samples of the user area and memory card will
be loaded into memory at power-on (ON) or not (OFF).
Value:
OFF, ON
Power Up Mode
This setting allows you to choose the mode that you want the
Fantom-S to be in when it is powered up.
Value
PATCH:
The Fantom-S will be in Patch mode when you
turn on the power.
PERFORMANCE:
The Fantom-S will be in Performance mode when
you turn on the power.
SRX/RAM Mode
The Fantom-S provides four slots (A–D) for SRX series expansion
boards. This setting specifies whether all of these slots will be
available (x4) or only slots A and B will be available (x2). If you have
installed a 256 MB DIMM module, setting this to “2 SRX/288MB
Max” will change the amount of memory that will be available as
sample memory.
* If a 512 MB DIMM is installed, the result will be the same as if a 256
MB DIMM were installed.
Range
2 SRX/288MB Max:
Only EXP slots A and B will be available.
4 SRX/192MB Max:
EXP slots A–D will all be available.
* The settings of this switch takes effect when the power is turned on.
System Information
For details on the indicating, refer to
“How to Make the System
Function Settings”
(p. 188).
Features
Displays the main features of the Fantom-S.
Memory Info (Memory Information)
Displays the amount of memory installed.
SRX Info (SRX Information)
Displays the name of the wave expansion board that is installed.
Version Info (Version Information)
Displays the version of the Fantom-S.
Installed DIMM
Amount of available
sample memory
512 MB
288 MB
256 MB 288 MB
128 MB 160 MB
64 MB 96 MB
0 MB 32 MB
Installed DIMM Amount of available
sample memory
512 MB 192 MB
256 MB 192 MB
128 MB 160 MB
64 MB 96 MB
0 MB 32 MB
Reference_e.book 195 ページ ２００３年７月１４日 月曜日 午後３時２５分