Filter
Top Products
E2-3
2. SPECIFICATIONS
ENGLISH VERSION EO1-33016
NOTES:
1. The media specification other than above are unchanged.
2. When marking black marks on label rolls, the following requirements must be satisfied.
When the gap length is less than 4 mm:
The black mark length should be longer than the gap length.
When the gap length is 4 mm or more:
The black mark should not overlap the gap for more than 4 mm and the following label.
3. When the print speed is 8"/sec., the width including backing paper will be 84 to 150 mm. When the optional cutter
module or strip module is used, the width including backing paper will be 101.6 to 175 mm.
4. If the label used is smaller than specified, the print head life may be shortened.
5. When issuing thermal labels at 8"/sec., the print stop position should be set to a minimum of 1 mm inside the label.
2.4 RIBBON
NOTES:
1. “On the fly issue” means that the printer can draw and print without stopping
between labels.
2. To ensure print quality and print head life use
only TOSHIBA TEC specified media
and ribbons.
3. When using the cutter ensure that label length
B
plus inter label gap length
E
exceeds 35 mm. (i.e. label pitch should be greater than 35 mm.)
4. To avoid ribbon wrinkles use the ribbon which is wider than media by 5mm or more.
However, too much difference in width between the two may cause wrinkles.
5. When the print speed is 8"/sec., the width will be 115 to 160 mm.
Type Spool type
Width 115 mm ~ 185 mm
(See NOTE 5.)
Length 300 m
Outer diameter Ø72 mm (max.)
2.3 MEDIA
2.3 MEDIA
Fig. 2-1
I I
J
H
H
G
G
D
C
C
1
1
2
2
A
A
F
B
E
Stop
position
Cut
position
Label
Reference
coordinate
Reference
coordinate
Refer to the following
NOTE 2.
Black Mark
(on reverse side)
Stop
position
Cut
position
Feed direction
Tag paper
Black Mark
(on reverse side)
Tag paper
Reference
coordinate
Reference
coordinate
Item
Label dispensing mode
Batch mode Strip mode
10.00 ~ 999.0 25.4 ~ 999.0
7.5 ~ 996.5 22.9 ~ 996.5
84.0 ~ 175.0 (See NOTE 3.)
81.0 ~ 172.0
2.5 ~ 10.0
1.0
Refer to the following NOTE 2.
149.3
490.6
Ø200 Max.
0.13 ~ 0.17
0.10 ~ 0.17
10.0 ~ 170.6
25.0 ~ 993.0
5.5 ~ 298.6 20.9 ~ 298.6 23.0 ~ 298.6
5.5 ~ 981.3 20.9 ~ 981.3 23.0 ~ 981.3
8.0 ~ 298.6 23.4 ~ 298.6 23.4 ~ 298.6
8.0 ~ 981.3 23.4 ~ 981.3 23.4 ~ 981.3
2.5 ~ 20.0 2.5 ~ 20.0 6.0 ~ 20.0
Label: 38 ~ 999.0
Tag: 25.4 ~ 999.0
Cut mode
A:
Span of one label/tag
B
: Label length
C
: Width including backing paper
D
: Label width
E
: Gap length
F
: Black mark length (Tag paper)
G
: Effective print width
:
Effective
print length
Label
Standard
Max. memory
Standard
Max. memory
Standard
Outer roll diameter
Max. memory
Label
Thickness
Tag
Tag
I
: Print speed up/slow down area
J
: Black mark length (Label)
Maximum effective
length for on the fly issue
H
[Unit: mm]