Filter
Top Products
22
SIBTF10xx-1xx-Mx
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Technical Specifications
For use with Transition Networks Model SIBTF10xx-1xx-Mx or equivalent.
Standards: IEEE 802.3™ 2000, IEEE 802.3x™
Data Rate: 10 Mb/s, 100 Mb/s (copper), 100 Mb/s (fiber)
Dimensions: Models 130- & 140-Mx
(W x H x D) 4.125" x 6" x 5" (104.77 x 152.4 x 127 mm)
Dimensions: Model 110-Mx
(W x H x D) 3.375" x 6" x 5" (85.73x 152.4 x 127 mm)
Weight: 3.2 lb. (1.5 kg) approximately
Input Voltage: 48–170VDC +/-15%
90–125VAC +/-15%, 50/60 Hz
Power: 15 W (maximum)
Aux input standby power, 200 mW typically
Fuse: 2.5 A/250 VDC
Alarm Relay: Three-position screw terminal block for the dry contact relay
0.5 A @ 125 VAC / 2.0 A @ 30 VDC (maximum)
switching capacity: 60 W (maximum)
Packet Size: Memory: 64K Bytes
Unicast MAC addresses: 1000
Maximum packet size: 1536 Bytes
MTBF*: 51,115 MIL-HDBK-217F Hours
153,038 Bellcore Hours
Environment
Operating Temp: -40 to 75°C (-40 to 167°F)
Storage Temp: -40 to 85°C (-40 to 185°F)
Humidity: 5 to 95%, non-condensing
Altitude: 3000 m (10,000 ft.)
Warranty: Lifetime
The industrial switch is designed for installation in restricted access locations.
Installing the industrial switch into other equipment or facility control rooms must
comply with the fire-enclosure requirements of IEC60950/EN60950/UL60950, along
with other local, national fire and safety codes.
IMPORTANT:
Copper based media ports: e.g., Twisted Pair (TP) Ethernet, USB,
RS232, RS422, RS485, DS1, DS3, Video Coax, etc. are intended for connecting to
intra-building (inside plant) link segments, not subject to lightening transients or
power faults. Copper based media ports: e.g., Twisted Pair (TP) Ethernet, USB,
RS232, RS422, RS485, DS1, DS3, Video Coax, etc. are NOT for connecting to inter-
building (outside plant) link segments subject to lightening transients or power faults.
*MTBF is estimated using the predictability method. This method is based on MIL-
217F at 25°C ambient temperature, typical enclosure heat rise of 10°C, and nominal
operating conditions and parameters. Installation and configuration specific MTBF
estimates are available upon request. Contact Technical Support.
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
23
Technical Specification -- continued
220–240VAC, 50/60Hz installation
CAUTION: If the main power source is 220-240VAC @50/60Hz, use a 2:1, 50VA or
greater step-down transformer between the main power source and the industrial
switch. Failure to observe this caution could result in a damaged switch.
Standard Description Compliance Level Remarks
EN55022/FCC Part15 ITE Emissions Class A Conducted and radiated
EN55024/EN61000-6-2: ITE Emissions
IEC61000-4-2 Level 2 ESD contact discharge
IEC61000-4-3 Level 4 Radiated fields
IEC61000-4-4 Level 3 Fast transients - power port
2 meter cable AC
1 meter cable DC
Level 2 Fast transient – Ethernet port
3 meter cable length
IEC6100-4-5 Level 3 CM
Level 2 DM
Level 1 DC
Surge – power port
2 meter cable AC
1 meter cable DC
Level 2 Surge – relay port
1 meter cable length
Level 2 Surge – Ethernet port
3 meter cable length
IEC61000-4-5 EN61000-6-2 Level 3
EN55024 Level 2
Conducted – power port
2 meter cable AC,
1 meter cable DC
EN61000-6-2 Level 3
EN55024 Level 2
Conducted – relay port
1 meter cable length
EN61000-6-2 Level 3
EN55024 Level 2
Conducted – PE Studs
2 meter cable length
EN61000-6-2 Level 3
EN55024 Level 2
Conducted – Ethernet port
10 meter cable length
IEC61000-4-8 Level 1 Power freq. mag. field
IEC61000-4-11 N/A VoltageDIPs and variations
IEEE1613, Power Substation Testing
IEEE1613, Clause 6.2 Not rated Dielectric power freq.
IEEE1613, Clause 6.3 Compliant Impulse voltage all ports
IEEE1613, Clause 7.3.1 Class 2 transverse and
common Mode
Surge oscillatory waveform
–power AC
Class 2 transverse and
common Mode
Surge oscillatory waveform
–power DC
Class 2 common mode Surge oscillatory waveform
–relay port
Class 2 common mode Surge oscillatory waveform
–Ethernet 10 Mbps
Class 1 common mode Surge oscillatory waveform
– Ethernet 100 Mbps
EMC Type Tests (all test were performed using unshielded cables)