Filter
Top Products
GS / m
[Name]
[Format]
[Range]
[Description]
Print downloaded bit image
ASCII GS / m
Hex 1D 2F m
Decimal 29 47 m
0 m 3, 48 m 51
Prints a downloaded bit image using the mode
specified by m.
Modes that can be selected by m are shown below.
GS n1 n2 d1...d(n1 x n2 x 8)
[Name]
[Format]
[Range]
[Description]
[Details]
[See Also]
Define downloaded bit image
ASCII GS * n1 n2 d1...d(n1 x n2 x 8)
Hex 1D 2A n1 n2 d1...d(n1 x n2 x 8)
Decimal 29 42 n1 n2 d1...d(n1 x n2 x 8)
1 n1 255, 1 n2 48, n1 x n2 1536 , 0 d 255
Defines a downloaded bit image using the number of dots
specified by n1 and n2
n1 specifies the number of dots in the horizontal direction.
n2 specifies the number of dots in the vertical direction.
The number of dots in the horizontal direction is n1 x 8, in the
vertical direction it is n2 x 8.
If n1 x n2 is out of the specified range, this command is disabled.
The d indicates bit-image data. Data (d) specifies a bit printed to 1
and not printed to 0.
The downloaded bit image definition is cleared when:
1. ESC @ is executed.
2. Printer is reset or the power is turned off.
The following figure shows the relationship between the
downloaded bit image and the printed data.
GS /
d1
d2
dn2
dn2 + 2
dn2 + 2
dn2 + 2 + 1
dn2 + 2 + 1
n2 x 8 dost
n1 x 8 dost
d 2 x n2 x 8
MSB
LSB
dn2 x 2
23
[Details]
[See Also]
When data exist in the print buffer, this command is ignored.
When a downloaded bit image has not been defined, this
command is ignored.
A portion of a downloaded bit image exceeding one line length is
not printed.
A downloaded character and a downloaded bit image cannot be
defined simultaneously.
GS *
0,48
1,49
2,50
3,51
NORMAL MODE
DOUBLE WIDTH MODE
DOUBLE HEIGHT MODE
QUADRUPLE SIZE MODE
Dot Density in
Vertical Direction
203 DPI
203 DPI
101 DPI
101 DPI
Dot Density in
Horizontal Direction
203 DPI
101 DPI
203 DPI
101 DPI
m
Mode Name
[Name]
[Format]
[Range]
[Description]
[Details]
(1) GS V m
(2) GS V m n
Select cut mode and cut paper
(1) ASCII GS V m
Hex 1D 56 m
Decimal 29 86 m
(2) ASCII GS V m n
Hex 1D 56 m n
Decimal 29 86 m n
(1) m = 1 , 49
(2) m = 66, 0 n 255
Performs the specified paper cutting.
For (1) and (1) :
This command is effective only processed at the beginning of a line.
For (1) :
Only the partial cut is available; there is no full cut.
For (2) :
When n = 0, the printer feeds the paper to the cutting position and
cuts it.
When n 0, the printer feeds the paper to (cutting position + [n x
vertical motion unit]) and cuts it.
The paper feed amount is calculated using the vertical motion
unit (y). However, the value cannot be less than the minimum
horizontal movement amount, and it must be in even units of the
minimum horizontal movement amount.
Partial cut (one point left uncut)
Feeds paper (cutting position + [n x (vertical motion unit)]),
and cuts the paper partially (one point left uncut).
Print mode
m
1, 49
66
24
RP-3180 USER'S MANUAL RP-3180 USER'S MANUAL