19
MZ-RH910
4. Press the [VOL+]/[VOL--] key and set the according value to
each destination referring to the following table.
5. Press the X key on the set or – key on the remote
commander to write the adjusted value.
6. Press the > key to select the item number 0114.
7. Repeat adjustment from step 3.
8. Press the x key four times and back to the Display Check
mode.
Destination
Setting value
Item No. 0113 Item No. 0114
US, Canadian, E, Mexican,
Hong Kong, Korean, Australian and 20 80
Tourist
AEP, UK and East European A0 80
Table 3-5-2. Destination Setting
4. Press the > key once to select the item number 0211.
5. Adjust with [VOL+]/[VOL--] keys so that the adjustment value
of LCD becomes calculated value.
6. Press the X key on the set or – key on the remote
commander to write the adjusted value.
7. Press the > key to next item.
8. Repeat adjustment from step 4 until item number 0216.
3-5-2. Destination setting
Procedure:
1. Enter the test mode (Display Check mode).
2. Press the [VOL+] key to enter the Manual mode.
3. Press the > key five time to select the item number 0113
and display as follows.
Display of the remote commander
Example of Calculation:
Item No. Parameter
Result
Decimal Hexadecimal
0211 Pr_nominal 2.48 mW 50 32h
0212 Kr −0.3 %/°C30 1Eh
0213 Pw_nominal 7.35 mW 147 93h
0214 Kw −0.4 %/°C40 28h
0215 Prmin 1.9 mW 38 26h
0216 Pwmin 5.8 mW 116 74h
Procedure:
1. Enter the test mode (Display Check mode).
2. Press the [VOL+] key to enter the Manual mode.
3. Press the > key once, press the [VOL+] key once, and press
the > key once again to display as follows.
Display of the remote commander
3-5-3. Other setting
Procedure:
1. Enter the test mode (Display Check mode).
2. Press the [VOL+] key to enter the Manual mode.
3. Press the [VOL+] key once and press the > key five time to
select the item number 1113 and display as follows.
Display of the remote commander
210 DiscPr
adjustment value (hexadecimal
113 DistFL **
4. Adjust with [VOL+]/[VOL--] keys so that the adjustment value
of “**” on the LCD becomes “1A”.
5. Press the X key on the set or – key on the remote
commander to write the adjusted value. ($$ blinks and disc
mark rotates on the LCD)
6. Adjust with [VOL+]/[VOL--] keys so that the adjustment value
of “$$”on the LCD becomes “20”.
7. Press the X key on the set or – key on the remote
commander to write the adjusted value. (## blinks and disc
mark rotates on the LCD)
8. Adjust with [VOL+]/[VOL--] keys so that the adjustment value
of “##”on the LCD becomes “94”.
9. Press the X key on the set or – key on the remote
commander to write the adjusted value.
10. Press the [VOL+] key once to change the adjustment value of
“**” on the LCD into “1B”.
11. Press the X key on the set or – key on the remote
commander to write the adjusted value. ($$ blinks and disc
mark rotates on the LCD)
12. Adjust with [VOL+]/[VOL--] keys so that the adjustment value
of “$$”on the LCD becomes “F1”.
13. Press the X key on the set or – key on the remote
commander to write the adjusted value. (## blinks and disc
mark rotates on the LCD)
14. Adjust with [VOL+]/[VOL--] keys so that the adjustment value
of “##”on the LCD becomes “1A”.
15. Press the X key on the set or – key on the remote
commander to write the adjusted value.
16. Press the x key four times and back to the Display Check
mode.
adjustment value (hexadecimal)
113 SS**$$##
