Filter
Top Products
BROAD SCAN (HD/SDI) APPENDIX A / ANNEXE A
PAGE 39
A-4: COMMANDS AND RESPONSES TABLE A-4: TABLE DES COMMANDES ET RÉPONSES
COMMAND RESPONSE COMMAND DESCRIPTION VALUE /VALEUR
COMMANDE RÉPONSE DESCRIPTION DE LA COMMANDE
TYPE
MIN MAX DESCRIPTION
FRONT PANEL COMMANDS / COMMANDES DE LA FACE AVANT
ws ws Standby function (ON/OFF) Rd/Wr 0 1 0 = ON 1 = OFF
CN CN Frame selection Rd/Wr 0 1 0 = OFF 1 = ON
OB OB Black function Rd/Wr 0 1 0 = Black inactive 1 = Black active
FZ FZ Freeze function. Rd/Wr 0 1 0 = Freeze inactive 1 = Freeze active.
OV OV Under/Overscan mode selection. Rd/Wr 0 1 0 = Underscan. 1 = Overscan.
OA OA Output aspect ratio Rd/Wr 0 2 0 = 1:1 1 = Full screen
2 = Crop
HP HP Horizontal position adjustment. Rd/Wr 0 255
VP VP Vertical position adjustment. Rd/Wr 0 255
HW HW Horizontal size adjustment. Rd/Wr 0 255
VS VS Vertical size adjustment. Rd/Wr 0 255
ZM ZM Zoom mode selection Rd/Wr 0 2 0 = zoom OFF 1 = zoom ON
2 = zoom finder ON
ZH ZH Zoom horizontal position. Rd/Wr 0 255
ZV ZV Zoom vertical position. Rd/Wr 0 255
ZW ZW Zoom horizontal size. Rd/Wr 100 10000
ZS ZS Zoom vertical size. Rd/Wr 100 10000
100 = 10% (x0.1)
1000 =100% (no zoom)
10000 = 1000% (x10)
yC yC Auto-centering Rd/Wr 0 1 1 = auto centering (automatic reset).
INPUT COMMANDS / COMMANDES D’ENTREE
az az Auto setting Rd/Wr 0 1 1 = auto setting (automatic reset).
PR PR Input type Rd/Wr 0 3 0 = Computer (SOG)
1 = Computer (H&V or Composite sync.)
2 = Computer DVI-D
3 = Computer B&W
PL PL H sync load selection. Rd/Wr 0 1 0 = Hi-Z 1 = 75 ohms.
OUTPUT COMMANDS / COMMANDES DE SORTIE
OF OF Output standard selection Rd/Wr 0 7 0 = NTSC 1 = PAL
2 = 480p 3 = 720p
4 = 1035i 5 = 1080i
6 = 1080sF 7 = 1080p
OR OR Output frame rate Rd/Wr 0 7 0 = 23.97 Hz 1 = 24 Hz
2 = 25 Hz 3 = 29.97 Hz
4 = 30 Hz 5 = 50 Hz
6 = 59.94 Hz 7 = 60 Hz
XR XR Synchronization mode selection. Rd/Wr 0 2 0 = internal.
1 = genlock.
2 = frame lock
XH XH H Phase genlock adjustment Rd/Wr
32722 32814
XS XS SC phase genlock adjustment Rd/Wr 0 1023
OZ OZ Output type selection. Rd/Wr 0 2 0 = RGBS.
1 = RGsB (SOG).
2 = YUV.
EP EP Pedestal (NTSC output only) Rd/Wr 0 1 0 = OFF 1 = ON
OP OP Test pattern selection. Rd/Wr 0 4 0 = no test pattern. 1 = grey scale
2 = color bar 3 = grid
4 = SMPTE
NOTE: Rd = Read only command / Commande de lecture. Rd/Wr = Read and write command / Commande de lecture et d'écriture.