Filter
Top Products
PJWU-101B 17/10/2014
4
1.SAFETY
•
Ensure that nothing can be spilled on, or dropped inside the projector. If this does happen, switch off and unplug the
mains supply immediately. Do not operate the projector again until it has been checked by qualified service personnel.
•
Do not block the projector cooling fans or free air movement around the projector. Loose papers or other objects may not
be nearer to the projector than 30 cm (12") on any side.
•
Do not use this equipment near water.
•
Special care for Laser Beams:Special care should be used when DLP projectors are used in the same room as high power
laser equipment. Direct or indirect hitting of a laser beam on to the lens can severely damage the Digital Mirror Devices
TM in which case there is a loss of warranty.
•
Never place the projector in direct sun light. Sun light on the lens can severely damage the Digital Mirror Devices TM in
which case there is a loss of warranty.
•
Save the original shipping carton and packing material. They will come in handy if you ever have to ship your equipment.
For maximum protection, repack your set as it was originally packed at the factory.
•
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth
for cleaning. Never use strong solvents, such as thinner or benzine, or abrasive cleaners, since these will damage the
cabinet. Stubborn stains may be removed with a cloth lightly dampened with mild detergent solution.
•
To ensure the highest optical performance and resolution, the projection lenses are specially treated with an anti-
reflective coating, therefore, avoid touching the lens. To remove dust on the lens, use a soft dry cloth. Do not use a damp
cloth, detergent solution, or thinner.
•
Rated maximum ambient temperature, ta= 40 °C (104 °F).
•
The lamp house shall be replaced if it has become damaged or thermally deformed.
On servicing
•
Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage
potentials and risk of electric shock.
•
Refer all servicing to qualified service personnel.
•
Attempts to alter the factory-set internal controls or to change other control settings not specially discussed in this manual
can lead to permanent damage to the projector and cancellation of the warranty.
•
Unplug this product from the wall outlet and refer servicing to qualified service technicians under the following conditions:
- When the power cord or plug is damaged or frayed.
- If liquid has been spilled into the equipment.
- If the product has been exposed to rain or water.
- If the product does not operate normally when the operating instructions are followed. Adjust only those controls that
are covered by the operating instructions since improper adjustment of the other controls may result in damage and will
often require extensive work by a qualified technician to restore the product to normal operation.
- If the product has been dropped or the cabinet has been damaged.
- If the product exhibits a distinct change in performance, indicating a need for service.
•
Replacement parts: When replacement parts are required, be sure the service technician has used original Barco
replacement parts or authorized replacement parts which have the same characteristics as the Barco original part.
Unauthorized substitu- tions may result in degraded performance and reliability, fire, electric shock or other hazards.
Unauthorized substitutions may void warranty.
•
Safety check: Upon completion of any service or repairs to this projector, ask the service technician to perform safety
checks to determine that the product is in proper operating condition.
•
Possible explosion hazard: Always keep in mind the caution below:
CAUTION: Do not touch a lamp during operation and right after it is turned off as it is extremely hot. Lamp
contains mercury. It's brokeage might cause mercury or broken glass pieces to folow out of lamp housing.
To avoid exposure the risk of mercury poisoning. Don't drop, hit, force or scratch while handing a lamp.
To prevent battery explosion
•
Danger of explosion if battery is incorrectly installed.
•
Replace only with the same or equivalent type recommended by the manufacturer.
•
For disposal of used batteries, always consult federal, state, local and provincial hazardous waste disposal rules and
regulations to ensure proper disposal.
•
Battery type: size-AAA (R03). Only Carbon-Zinc or Alkaline-Manganese Dioxide type batteries should be used.