Filter
Top Products
CY7C1353G
Document #: 38-05515 Rev. *E Page 3 of 13
Pin Definitions
Name IO Description
A
0
, A
1
, A Input-
Synchronous
Address Inputs used to select one of the 256K address locations. Sampled at the rising edge
of the CLK. A
[1:0]
are fed to the two-bit burst counter.
BW
[A:B]
Input-
Synchronous
Byte Write Inputs, Active LOW. Qualified with
WE to conduct writes to the SRAM. Sampled on
the rising edge of CLK.
WE
Input-
Synchronous
Write Enable Input, Active LOW. Sampled on the rising edge of CLK if CEN is active LOW. This
signal must be asserted LOW to initiate a write sequence.
ADV/LD Input-
Synchronous
Advance/Load Input. Used to advance the on-chip address counter or load a new address. When
HIGH (and CEN
is asserted LOW) the internal burst counter is advanced. When LOW, a new
address can be loaded into the device for an access. After being deselected, ADV/LD
must be
driven LOW to load a new address.
CLK Input-Clock Clock Input. Used to capture all synchronous inputs to the device. CLK is qualified with CEN. CLK
is only recognized if CEN
is active LOW.
CE
1
Input-
Synchronous
Chip Enable 1 Input, Active LOW. Sampled on the rising edge of CLK. Used in conjunction with
CE
2
, and CE
3
to select/deselect the device.
CE
2
Input-
Synchronous
Chip Enable 2 Input, Active HIGH. Sampled on the rising edge of CLK. Used in conjunction with
CE
1
and CE
3
to select/deselect the device.
CE
3
Input-
Synchronous
Chip Enable 3 Input, Active LOW. Sampled on the rising edge of CLK. Used in conjunction with
CE
1
and
CE
2
to select/deselect the device.
OE Input-
Asynchronous
Output Enable, asynchronous input, Active LOW. Combined with the synchronous logic block
inside the device to control the direction of the IO pins. When LOW, the IO pins are allowed to
behave as outputs. When deasserted HIGH, IO pins are tri-stated, and act as input data pins. OE
is masked during the data portion of a write sequence, during the first clock when emerging from
a deselected state, when the device has been deselected.
CEN
Input-
Synchronous
Clock Enable Input, Active LOW. When asserted LOW the Clock signal is recognized by the
SRAM. When deasserted HIGH the Clock signal is masked. While deasserting CEN
does not
deselect the device, CEN
can be used to extend the previous cycle when required.
ZZ Input-
Asynchronous
ZZ “sleep” Input. This active HIGH input places the device in a non-time critical “sleep” condition
with data integrity preserved. During normal operation, this pin has to be low or left floating. ZZ pin
has an internal pull down.
DQ
s
IO-
Synchronous
Bidirectional Data IO Lines. As inputs, they feed into an on-chip data register that is triggered by
the rising edge of CLK. As outputs, they deliver the data contained in the memory location specified
by address during the clock rise of the read cycle. The direction of the pins is controlled by OE and
the internal control logic. When OE
is asserted LOW, the pins can behave as outputs. When HIGH,
DQ
s
and DQP
[A:B]
are placed in a tri-state condition. The outputs are automatically tri-stated during
the data portion of a write sequence, during the first clock when emerging from a deselected state,
and when the device is deselected, regardless of the state of OE
.
DQP
[A:B]
IO-
Synchronous
Bidirectional Data Parity IO Lines. Functionally, these signals are identical to DQ
s
. During write
sequences, DQP
[A:B]
is controlled by BW
x
correspondingly.
MODE Input
Strap Pin
MODE Input. Selects the burst order of the device.
When tied to Gnd selects linear burst sequence. When tied to V
DD
or left floating selects interleaved
burst sequence.
V
DD
Power Supply Power supply inputs to the core of the device.
V
DDQ
IO Power
Supply
Power supply for the IO circuitry.
V
SS
Ground Ground for the device.
NC,NC/9M,
NC/18M,
NC/36M
NC/72M,
NC/144M,
NC/288M,
– No Connects. Not internally connected to the die. NC/9M, NC/18M, NC/72M, NC/144M, NC/288M,
are address expansion pins are not internally connected to the die.
[+] Feedback