Filter
Top Products
CY7C1353G
Document #: 38-05515 Rev. *E Page 5 of 13
Linear Burst Address Table (MODE = GND)
First
Address
A1, A0
Second
Address
A1, A0
Third
Address
A1, A0
Fourth
Address
A1, A0
00 01 10 11
01 10 11 00
10 11 00 01
11 00 01 10
Interleaved Burst Address Table
(MODE = Floating or V
DD
)
First
Address
A1, A0
Second
Address
A1, A0
Third
Address
A1, A0
Fourth
Address
A1, A0
00 01 10 11
01 00 11 10
10 11 00 01
11 10 01 00
ZZ Mode Electrical Characteristics
Parameter Description Test Conditions Min Max Unit
I
DDZZ
Sleep mode standby current ZZ > V
DD
− 0.2V 40 mA
t
ZZS
Device operation to ZZ ZZ > V
DD
− 0.2V 2t
CYC
ns
t
ZZREC
ZZ recovery time ZZ < 0.2V 2t
CYC
ns
t
ZZI
ZZ active to sleep current This parameter is sampled 2t
CYC
ns
t
RZZI
ZZ inactive to exit sleep current This parameter is sampled 0 ns
Truth Table
[2, 3, 4, 5, 6, 7, 8]
Operation
Address
Used CE
1
CE
2
CE
3
ZZ ADV/LD WE BW
X
OE CEN CLK DQ
Deselect Cycle None H X X L L X X X L L->H Tri-State
Deselect Cycle None X X H L L X X X L L->H Tri-State
Deselect Cycle None X L X L L X X X L L->H Tri-State
Continue Deselect Cycle None X X X L H X X X L L->H Tri-State
READ Cycle (Begin Burst) External L H L L L H X L L L->H Data Out (Q)
READ Cycle (Continue Burst) Next X X X L H X X L L L->H Data Out (Q)
NOP/DUMMY READ (Begin
Burst)
External L H L L L H X H L L->H Tri-State
DUMMY READ (Continue Burst) Next X X X L H X X H L L->H Tri-State
WRITE Cycle (Begin Burst) External L H L L L L L X L L->H Data In (D)
WRITE Cycle (Continue Burst) Next X X X L H X L X L L->H Data In (D)
NOP/WRITE ABORT (Begin
Burst)
None L H L L L L H X L L->H Tri-State
WRITE ABORT (Continue Burst) Next X X X L H X H X L L->H Tri-State
IGNORE CLOCK EDGE (Stall) Current X X X L X X X X H L->H –
SLEEP MODE None X X X H X X X X X X Tri-State
Notes:
2. X =”Don't Care.” H = Logic HIGH, L = Logic LOW. BW
x = L signifies at least one Byte Write Select is active, BWx = Valid signifies that the desired byte write
selects are asserted, see truth table for details.
3. Write is defined by BW
X
, and WE. See truth table for Read/Write.
4. When a write cycle is detected, all IOs are tri-stated, even during byte writes.
5. The DQs and DQP
[A:B]
pins are controlled by the current cycle and the OE signal. OE is asynchronous and is not sampled with the clock.
6. CEN
= H, inserts wait states.
7. Device powers up deselected and the IOs in a tri-state condition, regardless of OE
.
8. OE
is asynchronous and is not sampled with the clock rise. It is masked internally during write cycles. During a read cycle DQs and DQP
[A:B]
= tri-state when OE
is inactive or when the device is deselected, and DQs and DQP
[A:B]
= data when OE is active.
[+] Feedback