Filter
Top Products
Configuration. Please wait...
detected and is being processed.
BIOS Update Attempt Failed!
Remote BIOS update attempt failed.
Retry the BIOS update. If problem persists, see Getting Help.
Caution! NVRAM_CLR jumper is installed
on system board.
NVRAM_CLR jumper is installed. CMOS has
been cleared.
Remove NVRAM_CLR jumper. See Figure6-1 for jumper
location.
CPUs with different cache sizes
detected!
Microprocessors with different cache sizes are
installed.
Ensure that all microprocessors have the same cache size and
that they are properly installed. See Processors.
Decreasing available memory
Faulty or improperly installed memory modules.
See Troubleshooting System Memory.
Error: Incorrect memory configuration
CPU n
The DIMM group for CPU n is incorrectly
configured and caused the system to halt.
See General Memory Module Installation Guidelines for memory
configuration information. If the problem persists, see
Troubleshooting System Memory.
!!*** Error: Remote Access Controller
initialization failure *** RAC virtual
USB devices may not be available...
Remote Access Controller initialization failure
Ensure that the Remote Access Controller is properly installed.
See Installing a RAC Card.
Gate A20 failure
Faulty keyboard controller; faulty system
board.
See Getting Help.
General failure
The operating system is unable to carry out
the command.
This message is usually followed by specific information. Note
the information, and take the appropriate action to resolve the
problem.
HyperTransport error caused a system
reset! Please check the system event
log for details!
A fatal system error occurred and caused the
system to reboot.
Check the SEL for information that was logged during the
error. See the applicable troubleshooting section in
Troubleshooting Your System for any faulty components
specified in the SEL.
Invalid NVRAM configuration, Resource
Re-allocated
System detected and corrected a resource
conflict.
No action is required.
Invalid PCIe card found in the
Internal_Storage slot!
The system halted because an invalid PCIe
expansion card is installed in the dedicated
storage controller slot.
Remove the PCIe expansion card and install either the internal
SAS controller in the dedicated slot.
Keyboard Controller failure
Faulty keyboard controller; faulty system board
See Getting Help.
Manufacturing mode detected
System is in manufacturing mode.
Reboot to take the system out of manufacturing mode.
Memory address line failure at address
,
read value expecting value
Memory double word logic failure at
address, read value expecting value
Memory odd/even logic failure at
address, read value expecting value
Memory write/read failure at address,
read value expecting value
Faulty or improperly installed memory modules.
See Troubleshooting System Memory.
Memory tests terminated by keystroke.
POST memory test terminated by pressing the
spacebar.
Information only.
No boot device available
Faulty or missing optical drive subsystem, hard
drive, or hard-drive subsystem, or no bootable
USB key installed.
Use a bootable USB key, CD, or hard drive. If the problem
persists, see Troubleshooting an SD Card or Internal USB Key
and Troubleshooting a Hard Drive. See Using the System Setup
Program for information on setting the order of boot devices.
No boot sector on hard drive
Incorrect configuration settings in System
Setup program, or no operating system on
hard drive.
Check the hard-drive configuration settings in the System
Setup program. See Using the System Setup Program. If
necessary, install the operating system on your hard drive.
See your operating system documentation.
No timer tick interrupt
Faulty system board.
See "Getting Help."
Optical drive not found
Cable is not properly seated, or drive missing.
See Troubleshooting an Optical Drive.
PCI BIOS failed to install
PCIe device BIOS (Option ROM) checksum
failure detected during shadowing.
Cables to expansion card(s) loose; faulty or
improperly installed expansion card(s).
Reseat the expansion card(s). Ensure that all appropriate
cables are securely connected to the expansion card(s). If the
problem persists, see Troubleshooting Expansion Cards.
PCIe Degraded Link Width Error:
Embedded device
Expected Link Width is n
Actual Link Width is n
Faulty system board or riser board.
See Getting Help.
PCIe Degraded Link Width Error:
Integrated device
Expected Link Width is n
Actual Link Width is n
The specified PCIe device is faulty or
improperly installed.
For a SAS controller daughter card, reseat the card in the
dedicated PCIe connector. See Installing a SAS Controller
Daughter Card. If the problem persists, see Getting Help.
PCIe Degraded Link Width Error: Slot n
Expected Link Width is n
Actual Link Width is n
Faulty or improperly installed PCIe card in the
specified slot.
Reseat the PCIe card in the specified slot number. See
Expansion Cards. If the problem persists, see Getting Help.
PCIe Training Error: Embedded device
Faulty system board or riser board.
See Getting Help.