A SERVICE OF

logo

22
Stylistic ST4000 Series Tablet PC User’s Guide – Section Two
If your system is equipped with a PC Card that allows
you to connect to a wired or wireless network, you
may be logged off the network after a period of
inactivity while system operation is suspended.
Contact your network administrator or help desk, or
call Fujitsu Service and Support at 1-800-8Fujitsu (1-
800-838-5487) for details on log-off parameters for
your network.
RESUMING SYSTEM OPERATION
To resume operation from either Suspend-to-RAM or
Hibernate modes, press the Suspend/Resume button.
From Suspend-to-RAM mode
Status lights indicate that the system state is
changing. It may take up to a minute before the
system returns to the On state and system operation
resumes. Note that the display turns on shortly
before the pen becomes active due to the power-up
sequences observed by the system.
From Hibernate (Save-to-Disk) mode
Active data is read from the hard disk drive, and the
system returns to the On state after a short time
.
Use the system as you normally would once system
operation resumes.
All programs resume at the point where execution
stopped when system operation was suspended.
ADJUSTING THE DISPLAY BRIGHTNESS
There are two ways to adjust the brightness of your
display:
Click the Tablet icon in the system tray at the bottom
right of the screen. (When the cursor is on top of the
icon, a message stating “Change tablet and pen set-
tings” is displayed.) When the Tablet and Pen Settings
window appears, select the Display tab, and move the
Screen Brightness slider to change the brightness.
Click Start -> Settings -> Control Panel -> Tablet and
Pen Settings. Select the Display tab, and move the
Screen Brightness slider to change the brightness.
USING THE PEN
You can use the Stylistic ST4000 Series pen to generate
and create electronic “ink”, to select items, and to navi-
gate through programs on the Tablet PC. Programs that
support handwriting recognition also allow you to write
characters directly on the screen with the pen. You can
also use the pen as a drawing tool.
Figure 2-1. Stylistic ST4000 Series Pen
The screen reacts when the pen tip is approximately 1/8
inch (3-5mm) from the screen. The pen has three
switches: a tip switch and a barrel button toggle switch
with switches at both ends. When activated, the tip
switch corresponds to the left mouse button, and the
front toggle (closest to the pen tip) barrel button switch,
when used in combination with the tip switch, corre-
POINT
Note that power to several system components must be
restored before system operation resumes. Allow
sufficient time for system operation to resume before
attempting to use the system. If your system uses
Hibernate mode, it will take longer to resume operation
as compared to using Suspend-to-RAM mode. Time is
needed to read data from the hard disk drive.
POINT
Depending upon whether you are running your system
on battery or AC power, the default screen brightness
settings will be different. The screen brightness default
for running on battery is lower than that on AC power
in order to optimize battery life.
POINT
The Stylistic ST4000 pen is a sophisticated, high-quality
electronic instrument that can be damaged if used
improperly. Treat the pen as you would any precision
device. The following list contains guidelines for proper
pen handling:
Do not gesture with the pen, use it as a pointer, or
tap it on surfaces other than the Tablet PC screen.
Do not try to turn the thumb grip on the pen; it is
designed for inserting and removing the pen from
the pen holder and for attaching a pen tether.
Never store the pen with the tip bearing the weight
of the pen (e.g., sitting tip down in a pencil cup).
Storing the pen tip down could distort the internal
mechanism over a period of time (especially in higher
temperatures), causing the tip to act as if it is always
depressed. To avoid damage, the pen should be
stored in the pen holder when not in use.
Pen Tether Attachment Point
Tip Switch
Barrel Switch
Alb_UG_Active B.book Page 22 Monday, October 21, 2002 12:15 PM