Filter
Top Products
EN-20
Menu operation (continued)
Menu Options
Set the following options provided in the respective menus.
1. QUICK MENU
•You cannot adjust COLOR TEMP. when WALL SCREEN in the INSTALLATION menu is set to other than OFF.
• When COLOR ENHANCER is switched, projected images may be distorted.
•The STANDARD lamp mode is activated by default whenever the projector is turned on. When the LOW LAMP MODE has been chosen, the
default STANDARD lamp mode is switched to the LOW lamp mode in 1 minute.
2. INFORMATION menu
noitpircsed erutaeFgnitteSnoitpo uneM
COLOR ENHANCER
AUTO
Automatically sets an optimal color balance based on the input signal.
Use this setting for most cases.
PRESENTATION Makes projected images bright and crisp.
STANDARD Makes projected images look natural.
THEATER Makes projected images soft and smooth. Best suited for movies.
USER Reflected by the value set in IMAGE menu. (See page 27.)
CONTRAST ± ).72 egap eeS( .segami detcejorp fo tsartnoc eht stsujdA03
BRIGHTNESS ± ).72 egap eeS( .segami detcejorp fo ssenthgirb eht stsujdA03
COLOR TEMP. 4 options
Adjusts the color temperature. (See page 27.)
SHARPNESS ± ).72 egap eeS( .segami detcejorp fo ssenprahs eht stsujdA5
LAMP MODE
STANDARD Select this setting when you want to view images in a well-lit room.
LOW
Select this setting when you want to view images at a moderate light
intensity. The operating sound is consequently reduced, and the lamp
lifetime becomes longer.
•When this mode is switched, projected images may flicker.
•I
f this mode is frequently switched, the lamp may be deteriorated.
ASPECT
AUTO
Select to change the aspect ratio automatically depending on the input
signal. (Select this option for normal use.)
16:9
Select to project images in full size (1920 x 1080 pixels) irrespective of
type of input signal.
NATIVE Select to project images in their original size as input.
.UNEM RESU TCELES ni detceles meti unem eht syalpsiDUNEM RESU
ti eht tceleSUNEM RESU TCELES em to display in USER MENU.
.UNEM LIATED ot sevoMUNEM LIATED
noitpircsed erutaeFnoitpo uneM
LAMP TIME (LOW)
This menu shows a lamp operating time (hour) calculated assuming that LAMP MODE is LOW.
•When the LAMP MODE is STANDARD, this menu shows a longer lamp operating time than
the actual time. (See page 38 for the interval of lamp replacement.)
•When the lamp operating time is 0 to 10 hours, "0H" is displayed. When the lamp operating
time exceeds 10 hours, the actual hours are displayed.
•When the lamp operating time reaches 3750 hours, the bar turns yellow. When it reaches
4750 hours, the bar turns red.
(The lamp lifetime is 5000 hours.)
.tupni gnieb si langis oediv detcejorp yltnerruc eht hcihw ot lanimret eht fo eman eht setacidnITUPNI
RESOLUTION Indicates the resolution of the currently projected video signal.
VERTICAL FREQUENCY Indicates the
vertical frequency of the currently projected video signal.
HORIZONTAL FRE-
QUENCY
Indicates the horizontal frequency of the currently projected video signal.
SYNC. TYPE Indicates the type of the sync signal for the currently projected video signal.
DETAIL MENU
SELECT
USER MENU
ASPECT
USER MENU
AUTO
OK
COLOR
QUICK MENU
CONTRAST
BRIGHTNESS
0
0
STANDARD
STANDARD
0
COLOR TEMP.
SHARPNESS
AUTO
COLOR
ENHANCER
LAMP MODE
LAMP TIME (LOW)
INPUT
RESOLUTION
VERTICAL
FREQUENCY
HORIZONTAL
FREQUENCY
SYNC. TYPE 5wire
60.02 KHz
75.04 Hz
1024x768
COMPUTER2
0 H
RG
HV
B
INFORMATION