Filter
Top Products
Index
Multi-Tech Systems, Inc. MT2456SMI-22 SocketModem Developer’s Guide 57
Index
$F – FastConnect Control, 33
%L - Report Line Signal Level, 24
%Q - Report Line Signal Quality, 24
&C - RLSD Option, 17
&D - DTR Option, 17
&F - Restore Factory Configuration (Profile), 14
&G - Select Guard Tone, 23
&K - Flow Control, 17
&P - Select Pulse Dial Make/Break Ratio, 23
&R - RTS/CTS Option, 18
&T - Local Analog Loopback Test, 14
&V - Display Current Configuration and Stored Profiles,
23
** - Load to Internal RA, 14
*B - Display Blacklisted Numbers, 24, 25
+ESA - Configure Synchronous Access Submode, 31
+ESR - Selective Repeat, 29
+GCI - Country of Installation, 13
+IBC – In Band Commands, 19
+IFC - DTE-Modem Local Flow Control, 18
+MS - Modulation Selection, 27
+PCW - Call Waiting Enable, 26
+VCID - Caller ID (CID), 12
+VDR - Distinctive Ring, 26
+VRID - Report Retrieved Caller ID (CID), 12
A - Answer, 22
B - ITU-T or Bell, 28
B - Transmit Break to Remote, 29
Country Certifications, 48
D - Dial, 21
Design considerations
Vendor recommendations, 49
E - Command Echo, 15
Electrical Characteristics, 9
EMC, Safety, and R&TTE Directive Compliance, 56
FCC Regulations, 52
G - Modem-to-Modem Flow Control (XON/XOFF), 18
H - Disconnect (Hang-Up), 22
Handling Precautions, 9
I - Identification, 13
International Modem Restrictions, 56
K - Break Control, 30
L - Speaker Volume, 22
Mechanical Specifications, 6
Multi-Tech Systems, Inc. Compliance, 52
N - Operating Mode, 12
New Zealand Telecom Warning Notice, 55
O - Return to On-Line Data Mode, 22
P - Set Pulse Dial Default, 22
Physical Dimensions, 6
Pin Configurations, 7
Placement, SocketModem, 51
Product Approvals, 48
Safety considerations, 50
Serial Demo Board block diagram, 47
South African Statement, Regulations, 56
Specifications,Mechanical, 6
Specifications,Technical, 5
–STE= - Set Telephony Extension, 25
T - Set Tone Dial Default, 22
Table of Result Codes, 16
Technical Specifications, 5
-TRV – Tip and Ring Voltage Measurement, 34
-TTE - Threshold Adjustments for Telephony Extension,
34
V.22bis Commands
$F – FastConnect Control, 33
%L - Report Line Signal Level, 24
%Q - Report Line Signal Quality, 24
&C - RLSD Option, 17
&D - DTR Option, 17
&F - Restore Factory Configuration (Profile), 14
&G - Select Guard Tone, 23
&K - Flow Control, 17
&P - Select Pulse Dial Make/Break Ratio, 23
&R - RTS/CTS Option, 18
&T - Local Analog Loopback Test, 14
&V - Display Current Configuration and Stored Profiles,
23
** - Load to Internal RA, 14
*B - Display Blacklisted Numbers, 24, 25
+ESA - Configure Synchronous Access Submode, 31
+ESR - Selective Repeat, 29
+ETBM - Call Termination Buffer Management, 29
+GCI - Country of Installation, 13
+IBC – In Band Commands, 19
+IFC - DTE-Modem Local Flow Control, 18
+MS - Modulation Selection, 27
+PCW - Call Waiting Enable, 26
+VCID - Caller ID (CID), 12
+VDR - Distinctive Ring, 26
+VRID - Report Retrieved Caller ID (CID), 12
A - Answer, 22
B - ITU-T or Bell, 28
\B - Transmit Break to Remote, 29
Call Control Commands, 21
D - Dial, 21
E - Command Echo, 15
FastConnect Command, 33
\G - Modem-to-Modem Flow Control (XON/XOFF), 18
Generic Modem Control, 12
H - Disconnect (Hang-Up), 22
I - Identification, 13
\K - Break Control, 30
L - Speaker Volume, 22
Line Side Device Commands, 34
M - Speaker Control, 23
Modulation Control Commands, 27
\N - Operating Mode, 12
O - Return to On-Line Data Mode, 22
P - Set Pulse Dial Default, 22
Q - Quiet Results Codes Control, 15