83-507-5002 Rev. B
TABLE OF CONTENTS
WARRANTY…………………………………………………………………………………………….
Pg. 1
SAFETY INSTRUCTIONS……………………………………………………………………………..
Pg. 2
GERMAN SAFETY INSTRUCTIONS…………………………………………………………………
Pg. 4
CHAPTER 1 GENERAL INFORMATION
…………………………………………………………...
Pg. 6
1.1 USER MANUAL CONTENT……………………………………………………………………….
Pg. 6
1.2 INTRODUCTION……………………………………………………………………………………
Pg. 6
1.
2.1 General description…………………………………………………………………………..
Pg. 6
1.2.2 Models covered ……………………………………………………………………………...
Pg. 6
1.2.3 Features and options ………………………………………………………………………..
Pg. 6
1.2.4 Multiple output power system ……………………………………………
…………………
Pg. 7
1.2.5 Control via the serial communication port…………………………………………………
Pg. 7
1.2.6 Analog voltage programming and monitoring…………………………………………….
Pg. 7
1.2.7 Parallel operation…………………………………………………………………………….
Pg. 7
1.2.8 Ou
tput connections………………………………………………………………………….
Pg. 7
1.2.9 Cooling and mechanical construction……………………………………………………..
Pg. 8
1.3 ACCESSORIES…………………………………………………………………………………….
Pg. 8
1.3.1 Included Accessories………………………………………………………………………..
Pg. 8
1.3.2 Optional Communication Cables……………………...…………………………………… Pg. 8
1.3.3 AC cables …………………………………………………………………………………….
Pg. 8
CHAPTER 2 SPECIFICATIONS
……………………………………………………………………...
Pg. 9
2.1 OUTPUT RATING………
………………………………………………………………………….
Pg. 9
2.2 INPUT CHARACTERISTICS……………………………………………………………………...
Pg. 9
2.3 CONSTANT VOLTAGE MODE…………………………………………………………………...
Pg. 9
2.4 CONSTANT CURRENT MODE…………………………………………………………………..
Pg. 9
2.5 ANALOG PROGRMAMING AND MONITORIN
G……………………………………………….
Pg. 9
2.6 PROGRAMMING AND READBACK……………………………………………………………..
Pg. 10
2.7 PROTECTIVE FUNCTIONS………………………………………………………………………
Pg. 10
2.8 FRONT PANEL…………………………………………………………………………………….
Pg. 10
2.9 ENVIRONMENTAL CONDITIONS………………………………………………………
……….
Pg. 10
2.10 MECHANICAL…………………………………………………………………………………….
Pg. 10
2.11 SAFETY/EMC……………………………………………………………………………………..
Pg. 10
2.12 SUPPLEMENTAL CHARACTERISTICS……………………………………………………….
Pg. 11
2.13 OUTLINE DRAWINGS…………………………………………………………………………...
Pg. 12
CHAPTER 3 INSTALLATION………………………………………………………………………..
Pg. 13
3.1 GENERAL…………………………………………………………………………………………...
Pg. 13
3.2 PREPARATION FOR USE………………………………………………………………………...
Pg. 13
3.3 INITIAL INSPECTION……………………………………………………………………………...
Pg. 13
3.4 RACK MOU
NTING…………………………………………………………………………………
Pg. 14
3.4.1 Single
-
unit installation………………………..……………………………………………..
Pg. 14
3.4.2 Dual unit install
a
tion………..……………………………………………………………….
Pg. 14
3.4.3 GENH/RM Rack Mounting outline drawings.………………………
…………………….
Pg. 15
3.5 LOCATION MOUNTING AND COOLING……………………………………………………….
Pg. 15
3.6 AC SOURCE REQUIREMENTS………………………………………………………………….
Pg. 15
3.7 AC INPUT POWER CONNECTION……………………………………………………………...
Pg. 15
3.7.1 AC input conne
c
tor………………….…………………………
……………………………
Pg. 16
3.7.2 AC input cord………………………………………………………………………………..
Pg. 16
3.8 TURN
-
ON CHECKOUT PROCEDURE………………………………………………………….
Pg. 16
3.8.1 General……………………………………………………………………………………….
Pg. 16
3.8.2 Prior to operation…………………………………
………………………………………….
Pg. 16
3.8.3 Constant voltage check……………………………………………………………………..
Pg. 17
3.8.4 Constant current check……………………………………………………………………..
Pg. 17
3.8.5 OVP check…………………………………………………………………………………...
Pg. 17
3.8.6 UVL chec
k……………………………………………………………………………………
Pg. 17
3.8.7 Foldback check……………………………………………………………………………...
Pg. 18
3.8.8 Address se
t
ting……………….……………………………………………………………..
Pg. 18
3.8.9 Baud rate setting……………………………………………………………………………. Pg. 18