Filter
Top Products
7
UCC/EAN Code 128
enabling/disabling...............................................2-12
UCC-128/ EAN-128 ................................................H-1
UNIX requirements and problems...................2-24, 8-5
UP ARROW key
transmitting ASCII 28 to host.............................6-12
UPC 2 and 5-character supplemental codes ..............J-2
UPC/EAN................................................................2-11
about.......................................................................J-1
Check digit.............................................................J-1
compressed format............................................... 2-12
default settings.......................................................2-11
guidelines for use....................................................J-2
NSC and check digit...........................................2-11
NSC's and check digits...........................................2-11
numbering conventions...........................................J-2
supplemental codes................................................2-11
UPC-A - adding a country code..............................2-11
UPC-A in 13 digit EAN format..............................2-11
UPC/EAN check digits - enabling transmission of 2-11
UPC/EAN checksum character..................................J-3
UPC/EAN Specifications...........................................J-1
UPC/EAN Supplements - enabling/disabling........2-11
UPC-E Checksum Calculation...................................J-4
UPC-E0 and UPC-E1..............................................2-12
UPC-E1 - enabling reading of................................2-13
Upgrading firmware in Base,Relay or Terminal .....D-1
US Date Format ......................................................2-18
USA/Canada/Mexico
EPROM version identification..............................2-6
Using Arrow Keys to transmit characters.................2-7
Using the bar code RF Terminal Setup Menu..........2-2
Using the Demo Programs before programming......5-2
Using the keypad to setup the RF Terminal .............2-3
Using the Relay instead of the Base to communicate4-4
Using the RF Terminal keypad.................................1-4
Using the Scan Stand...............................................M-1
Utilities CD..................................................................1-8
V
Vehicle ID reading....................................................L-3
Version
9075.......................................................................6-6
VIN reading...............................................................L-3
Voice Cloning Cable #T15.......................................7-5
Voice message "command" ......................................6-2
Voice message mapping............................................7-2
Voice Message Operations .......................................7-1
Voice message partitions - changing........................7-2
Voice Message Partitions...............................2-19, 2-20
Voice messages
cloning from RF Terminal to RF Terminal..........7-5
error conditions........................................................7-5
playback................................................................ 7-3
record error messages for all situations................7-2
Voice Messages
changing the time allotments....................................2-19
Voice Operations selection on SETUP Menu.......... 7-2
Voice Prompts
helping to limit mistakes....................................... 7-1
W
Waiting for Base to Acknowledge............................ 8-3
Waiting on Host Prompt...........................................8-3
WAITING ON HOST PROMPT.............................. 3-2
Waiting on Host Prompt problems...........................8-2
Waiting on Host Prompt” .........................................8-3
Wand vs. keypad entry.............................................. 6-3
wanding variable data...............................................E-4
Wanding variable data..............................................E-4
WDTRI password.....................................................2-3
What to do with data after a failure ...............................5-2
What to do with data after an operator error.............5-3
why recharging doesn't work..................................2-18
Why Use Voice Messages and Prompts?.................7-1
Windows 95 com port setup.........................................8-6
Windows ActiveX programming............................ 6-13
Windows RF Loader program................................. D-1
Windows TCP/IP terminal programming...............6-23
Windshield Reading..................................................L-3
Wrong data................................................................L-3
X
Xmit Setup/Voice Please Wait .................................7-5
XON/XOFF
changing ASCII characters to avoid conflict...... 6-11
XP - caution with connection pooling.....................8-2
Y
Year
2000 compliance................................................. 2-19
displaying 4 digits............................................... 2-19
YELLOW LED.........................................................8-4
YES/NO entry while scanning.................................. 6-3
Z
Zebra Cameo Magstripe input..................................6-3
Zebra Cameo Printer.......................................6-33, C-3
setup for use with RF Terminal..........................6-33
Zebra Encore Printer............................................... 6-34
Zebra magstripe ........................................................6-4