1
© Copyright 2005 Printed Manual No. 701-186M
Before You Start
Your Land Pride Winch Kit is designed for your Land
Pride Treker with optional Heavy Duty Brush Guard. It
will also fit 4200/4400 NT/ST Trekers with special winch
mounting plates. Please read these installation
instructions and the vehicle Operator’s Manual
thoroughly before beginning. Especiallyread information
relating to safety concerns. Also included in the
Operator’s Manual is importantinformation on operation,
adjustment, troubleshooting, and maintenance for this
attachment (some manual sections do not apply to all
accessories).
A separate Parts Manual for replacement parts can be
purchased from your dealer or available free of charge at
www.landpride.com. Have model and serial numbers
handy when placing an order.
Manual Part Numbers:
• Operator’s Manual (4220/4420). . . . . . . 700-504M
• Operator’s Manual (4210/4410). . . . . . . 700-108M
• Operator’s Manual (4200/4400 NT/ST) . 700-108M
• Parts Manual (4220/4420) . . . . . . . . . . . 700-504P
• Parts Manual (4210/4410) . . . . . . . . . . . 700-109P
• Parts Manual (4200/4400 NT/ST) . . . . . 700-108P
General Information
These assembly instructionsapply to the2500 Lb. Winch
Accessory listed below:
701-185A WINCH KIT FOR HD BRUSH GUARD
701-064A WINCH W/MOUNTING KIT 4200/4400 ST
701-065A WINCH W/MOUNTING KIT 4200/4400 NT
When you see this symbol, the subsequent
instructions and warnings are serious - follow
without exception. Your life and the lives of
others depend on it!
!
IMPORTANT: Before you begin, read these
instructions and check to be sure all parts and tools
are accounted for. Please retain these installation
instructions for future reference and parts ordering
information.
NOTE: The Brush Guard referred to in this manual
is optional on the ST 10 and 20 Series Treker.
However, this brush guard will fit the ST 00 Series
Treker and can be purchased through our parts
department by a Land Pride vehicle dealer.
Tools required:
• Safety glasses
• Work gloves
• Pliers, crimp pliers and wire strippers
• Electric drill & extension cord if needed
• 1/4", 5/32" & 7/8" twist drills or 7/8" hole saw
• Torque wrench complete with sockets below
• 1/2", 3/8", 9/16", M7, M10, M13 & M17 sockets
• 1/2", 3/8", 9/16", M7, M10, M13 & M17 box end
and/or open end wrenches
Assembly Instructions
A detailed listing of parts for each accessory kit is
provided on page 11. Use the list as a checklist to
inventory parts received. Please contact your local Land
Pride dealer for any missing hardware.
Initial Preparations
Before servicing the vehicle the following procedure
must be met to secure the vehicle:
1. Park vehicle on a level surface. Don’t work under or
around a vehicle parked on an incline.
2. Make the following gear and park brake selections:
a. 4200/4400 NT/ST Trekers:
•Set shift selector in forward gear.
•Set park brake.
b. 4210ST, 4410ST, 4220ST & 4420ST Trekers.
•Set shift selector in Park.
3. Turn ignition switch off and remove switch key.
4. Chock front and back of a wheel to prevent the
vehicle from rolling.
!
DANGER
Follow all safety requirements in this manual and the
2500 lb. Winch Instruction and Operation Manual. Your
Safety depends upon knowing how to mount and operate
the winch safely.
IMPORTANT:
Read and understand Basic Winch Operation and
Winch Safe Operating Procedures on pages 2
and 3 before mounting the winch.
Also, read and understand the 2500 lb. Winch
Instruction and Operation Manual provided with
the winch before mounting.
For 4200/4400 NT/ST, 4210/4410 ST And 4220/4420 ST
2500 Lb. Winch Mounting Instructions
11/30/06
Manual No. 701-186M
