Canon MF4890dw Printer User Manual


 
112
Users in the U.S.A.
Pre-Installation Requirements for Canon Facsimile Equipment
A. Location
Supply a suitable table, cabinet, or desk for the machine. See
Chapter 1
1, “Appendix,” for speci c dimensions and weight.
B. Order Information
1. A single telephone line (touch-tone or rotary) should be used.
2.
Order an RJ11-C telephone wall jack (USOC), which should be
installed by the telephone company. If the RJ11-C wall jack is
not present, telephone/facsimile operation is not possible.
3. Order a normal business line from your telephone company’s
business representative. The line should be a regular voice
grade line or an equivalent one. Use one line per unit.
DDD (Direct Distance Dial) line
-or-
IDDD (International Direct Distance Dial) line if you communicate
overseas
Canon recommends an individual line following
industry standards, i.e., 2,500 (touch-tone) or 500
(rotary/pulse dial) telephones. A dedicated extension
o a PBX (Private Branch eXchange) unit without “Call
Waiting” can be used with your facsimile unit. Key
telephone systems are not recommended because
they send nonstandard signals to individual
telephones for ringing and special codes, which may
cause a facsimile error.
C. Power Requirements
The machine should be connected to a standard 120 volt AC,
thre
e
-wire grounded outlet only.
Do not connect this machine to an outlet or power line
shared with other appliances that cause “electrical noise.” Air
conditioners, electric typewriters, copiers, and machines of
this sort generate electrical noise that often interferes with
communications equipment and the sending and receiving of
documents.
Connection of the Equipment
This equipment complies with Part 68 of the FCC rules and the
requirements adopted by the ACTA. On the rear panel of this
equipment is a label that contains, among other information,
a product identi er in the format of US:AAAEQ##TXXXX. If
requested, this number must be provided to the telephone
company.
The REN (Ringer Equivalence Number) is used to determine the
number of devices that may be connected to a telephone line.
Excessive RENs on a telephone line may result in the devices not
ringing in response to an incoming call. In most, but not all areas,
the sum of the RENs should not exceed  ve (5.0).
To be certain of the number of devices that may be connected to a
line, as determined by the total RENs, contact the local telephone
company. The REN for this product is part of the product identi er
that has the format US: AAAEQ##TXXXX. The digits represented by
## are the REN without a decimal point (e.g., 10 is a REN of 1.0).
An FCC compliant telephone line cable and modular plug is
provided with this equipment. This equipment is designed to be
connected to the telephone network or premise wiring using a
compatible modular jack that is Part 68 compliant.
This equipment may not be used on coin service provided by the
telephone company. Connection to party lines is subjected to
state tari s.
In Case of Equipment Malfunction
Should any malfunction occur which cannot be corrected by the
procedures described in this guide or the e-Manual, disconnect
the equipment from the telephone line cable and disconnect the
power cord.
The telephone line cable should not be reconnected or the power
switch turned ON until the problem is completely resolved. Users
should contact Canon Authorized Service Facilities for servicing
of equipment, Information regarding Authorized Service Facility
locations can be obtained by calling Canon Customer Care Center
(1-800-OK-CANON).
Rights of the Telephone Company
If this equipment (imageCLASS MF4890dw/MF4880dw/MF4770n)
causes harm to the telephone network, the telephone company
may temporarily disconnect service. The telephone company also
retains the right to make changes in facilities and services that may
a ect the operation of this equipment. When such changes are
necessary, the telephone company is required to give adequate
prior notice to the user.
However, if advance notice is not possible, the telephone
company will notify the customer as soon as possible. Also, the
customer will be advised of his/her right to  le a complaint with
the FCC if he/she believes it is necessary.
WARNING
The Telephone Consumer Protection Act of 1991 makes it
unlawful for any person to use a computer or other electronic
device, including FAX machines, to send any message unless such
message clearly contains in a margin at the top or bottom of each
transmitted page or on the  rst page of the transmission, the date
and time it is sent and an identi cation of the business or other
entity, or other individual sending the message and the telephone
number of the sending machine or such business, other entity, or
individual.
(The telephone number provided may not be a 900 number or
any other number for which charges exceed local or long-distance
transmission charges.)
In order to program this information into your
machine, you should complete the procedure for
registering your name, unit’s telephone number, time,
and date in the Starter Guide.
Users in Canada
Pre-Installation Requirements for Canon Facsimile Equipment
A. Location
Supply a suitable table, cabinet, or desk for the machine. See
Chapter 1
1, “Appendix,” for speci c dimensions and weight.
B. Order Information
1. A single telephone line (touch-tone or rotary) should be used.
2.
Order a CA11A modular jack, which should be installed by
the telephone company. If the CA11A jack is not present,
installation cannot occur.
3. Order a normal business line from your telephone company’s
business representative. The line should be a regular voice
grade line or an equivalent one. Use one line per unit.