Filter
Top Products
EPSON Stylus Scan 2500
3 -
EPSON Stylus Scan 2500
9/99
System Requirements
Windows
®
❏ An IBM
®
compatible PC with at least a 486/66 MHz
processor (Pentium
®
processor recommended)
❏ Microsoft
®
Windows 95 or 98
❏ At least 16 MB of RAM (32MB or more recommended)
❏ At least 50MB of free hard disk space (100MB
recommended)
❏ VGA or better display adapter and monitor (24-bit color
recommended)
❏ Double-speed (2x) CD-ROM drive for installing the
software (quad-speed [4x] or faster recommended) for
installing the software
Your system should also have one of the following interfaces
(USB recommended):
❏ Windows 98 only: Available USB port or hub connection,
with shielded USB “AB” interface cable, from Series A
(computer) to series B (EPSON Stylus Scan), up to 6.5 feet
(2 m) long*
❏ Windows 95 or 98: Available parallel port with a high-
speed, bidirectional, IEEE-1284-compliant parallel cable (6
to 10 feet long).The cable must have a D-SUB, 25-pin,
male connector for your computer and a 36-pin,
Centronics
®
compatible connector for the Stylus Scan.**
Caution:
Using an improperly shielded USB cable—especially a cable more
than 6.5 feet long—may cause the Stylus Scan to malfunction.
Notes:
* If you’re using a USB connection, Windows 98 must be
preinstalled on your system—not an upgrade from Windows 95.
* If you’re using a USB hub, use only a first tier hub (the hub
closest to the host computer).
** The EPSON Stylus Scan must be connected to a built-in
parallel port (LPT 1 only). It cannot be used with a switch box or
pass-through port (for example, on a Zip drive).
Macintosh
®
❏ iMac
®
series or other Macintosh computer with built-in
USB port
❏ Mac OS 8.1 or later (OS 8.5 or later recommended)
❏ At least 32MB of available memory (64MB recommended)
❏ At least 50MB of free hard drive space (100MB
recommended)
❏ VGA or better monitor (24-bit color recommended)
❏ Double-speed (2x) CD-ROM (quad-speed [4x] or faster
recommended) for installing the software
❏ Available USB port or hub connection, with shielded USB
“AB” interface cable, from Series A (computer) to Series B
(EPSON Stylus Scan), up to 6.5 feet (2 m) long
Note:
If your iMac is running Mac OS 8.1, you need to install the iMac
Update 1.0 before installing the EPSON Stylus Scan software. If your
iMac is running Mac OS 8.5 or 8.51, Apple recommends that you
install iMac Update 1.1.
These updates are available online from Apple at http://
swupdates.info.apple.com. Contact Apple if you have problems
installing them.
Specifications
Mechanical
Printing
Paper feed method Friction
Paper path Sheet feeder, rear entry
Sheet feeder capacity About 100 sheets at 17 lb (64 g/m²)
paper
Dimensions Storage
Width: 20.4 inches (517 mm)
Depth: 20.8 inches (529 mm)
Height: 11.8 inches (300 mm)
Printing
Width: 20.4 inches (517 mm)
Depth: 22.6 inches (575 mm)
Height: 11.8 inches (300 mm)
Weight 26.5 lb (12 kg) without the ink
cartridges
Printing method On-demand ink jet
Nozzle
configuration
Monochrome (black) 144 nozzles
Color (cyan, magenta, yellow)
144 nozzles
(48 [each color] × 3)
Resolution Maximum 1440 dpi × 720 dpi
Print direction Bidirectional with logic seeking
Control code ESC/P raster
EPSON Remote
Input buffer 64 KB