Extron electronic MPX Plus 866 A Switch User Manual


  Open as PDF
of 23
 
Refer also to the MPX Plus 866 A User’s Manual at www.extron.com.
Refer also to the MPX Plus 866 A User’s Manual at www.extron.com.
Command ASCII command
(host to switcher)
Response
(switcher to host)
Additional description
Create ties
N
•Videotiescannotbemadebetweenthecomputervideogroupandthelowresolutionvideogroup.
•Programaudiotiescanonlybemadetothecomputer/audiooutputgroup(outputs1through6).
•MixingaudioinputsintotheoutputaudiousingSIScommandsrequiresacomplexcommand.RefertotheMPX Plus 866 A User's
Manual.
•Videoandaudiotiesbetweenthelowresolutionvideoinputgroupandthelowresolutionvideooutputsgrouparealwaysmadewiththe
program audio redirected. In such an operation, the switcher automatically ties the audio to an output in the computer/audio outputs group
(outputs 1 through 6) as follows:
m
If the video is tied to output 7, the audio is tied to output 1. m If the video is tied to output 10, the audio is tied to output 4.
m If the video is tied to output 8, the audio is tied to output 2. m If the video is tied to output 11, the audio is tied to output 5.
m If the video is tied to output 9, the audio is tied to output 3. m If the video is tied to output 12, the audio is tied to output 6.
•
Commands can be entered back-to-back in a string, with no spaces. For example: 1*1!02*2&02*04%4*6$.
•
The matrix switchers support 1-, 2-, and 3-digit numeric entries (1*1!, 02*02&, or 003*003%).
N
The & tie command for RGB and the % tie command for video can be used interchangeably, but you cannot switch between groups.
N
The & read tie command for RGB and the % read tie command for video can be used interchangeably.
Tie input
X! to output X@, video
and audio
X!
*
X@
! Out
X@•
In
X!•
All
]
(within computer video group)
— or —
Qik
]
(within low resolution video group [because of audio redirect])
Tie input
X!
‘s video and audio to output
X@
.
Example:
1*3!
Out03
•
In01
•
All
]
Tie input 1 video and audio to output 3.
11*9!
Qik
]
Tie input 11 video to output 9
and input 11 audio to output 5.
N
X!
= Input number
00 – 08 (computer video input group) or 00, 09 – 14 (low resolution video input group) (00 = untied)
X@
= Output number 01 – 06 (Computer video and audio output group) or 07
– 12 (low resolution video output group)
N
X!
= Input number
00 – 08 (computer video input group) or 00, 09 – 14 (low resolution video input group) (00 = untied)
X@
= Output number 01 – 06 (Computer video and audio output group) or 07
– 12 (low resolution video output group)
X#
= video format 1 = composite video 2 = S-video
Command ASCII command
(host to switcher)
Response
(switcher to host)
Additional description
Create ties (continued)
Tie input
X! to output X@,
computer only
X!
*
X@
& Out
X@•
In
X!•
RGB
]
Audio breakaway.
Example:
(see 2nd Note, above)
5*4&
Out04
•
In05
•
RGB
]
Tie input 5 RGB to output 4.
Tie input
X! to output X@, video
only
X!
*
X@
% Out
X@•
In
X!•
Vid
]
Audio breakaway switching.
Example:
(see 2nd Note, above)
9*7%
Out07
•
In09
•
Vid
]
Tie input 9 video to output 7.
Tie input
X! to output X@, audio
only
X!
*
X@
$ Out
X@•
In
X!•
Aud
]
Audio breakaway switching.
Example:
12*4$
Out04
•
In12
•
Aud
]
Tie input 12 audio to output 4.
Read computer video output tie
X@
&
X!]
RGBHV input
X!
is tied to output
X@
.
Read video output tie
X@
%
X!]
Video input
X!
is tied to output
X@
.
Read audio output tie
X@
$
X!]
Audio input
X!
is tied to output
X@
.
Set input format
Set input video format
X!
*
X#
\ Typ
X!
*
X#]
Set the video format to
X#
for input
X!
.
N
The only valid input (
X!
) numbers are 11 through 14.
Example: 11*1\
Typ11*1
]
Set input 11 to composite video.
Read input format
X!
\
X#]
Show the video format of input
X!
.
MPX Plus 866 A • Remote Control
Remote Control, cont’d
4-4
MPX Plus 866 A • Remote Control
4-5
 previous next