Filter
Top Products
• Check the appearance of the unit when it is unpacked. Do not use the unit if any damage or deformation is
found. Failure to do so may lead to fire, damage or malfunction.
• For use in a facility or for a system related to nuclear energy, aerospace, medical, traffic equipment, or
mobile installations, please consult your local distributor.
• Operate (or store) POD under the conditions indicated in this manual and related manuals. Failure to do so
could cause fire, malfunction, physical damage or deterioration.
• Understand the following environmental limits for use and storage of POD. Otherwise, fire or damage to the
unit may result.
- Avoid locations where there is a possibility that water, corrosive gas, flammable gas, solvents, grinding
fluids or cutting oil can come into contact with the unit.
- Avoid high temperature, high humidity, and outside weather conditions, such as wind, rain or direct
sunlight.
- Avoid locations where excessive dust, salt, and metallic particles are present.
- Avoid installing the unit in a location where vibration or physical shock may be transmitted.
• Equipment must be correctly mounted so that the main terminal of POD will not be touched inadvertently.
Otherwise, an accident or electric shock may occur.
• Tighten the fixtures of the POD with a torque in the specified range. Excessive tightening may distort the
panel surface. Loose tightening may cause POD to come off, malfunction or be short-circuited.
• Check periodically that terminal screws on the power supply terminal block and fixtures are firmly tightened.
Loosened screws may result in fire or malfunction.
• Tighten terminal screws on the power supply terminal block equally to a torque of 0.5 N•m. Improper
tightening of screws may result in fire, malfunction, or trouble.
• POD has a glass screen. Do not drop or give physical shock to the unit. Otherwise, the screen may be
damaged.
• Connect the cables correctly to the terminals of POD in accordance with the specified voltage and wattage.
Over-voltage, over-wattage or incorrect cable connection could cause fire, malfunction or damage to the
unit.
• Be sure to establish a ground of POD. Ground FG terminal which must be used for the unit. Otherwise,
electric shock or a fire may occur.
• Prevent any conductive particles from entering into POD. Failure to do so may lead to fire, damage or
malfunction.
• After wiring is finished, remove the paper used as a dust cover before starting to operate POD. Operation
with the cover attached may result in accident, fire, malfunction, or trouble.
• Do not attempt to repair POD at your site. Ask us or the designated contractor for repair.
• Do not disassemble or modify POD. Otherwise, it may cause a malfunction.
• Fuji Electric FA Components & Systems Co., Ltd. is not responsible for any damages resulting from repair,
overhaul or modification of POD that was performed by an unauthorized person.
• Do not use a sharp-pointed tool when pressing a touch switch. Doing so may damage the screen.
• Only experts are authorized to set up the unit, connect the cables or perform maintenance and inspection.
• For POD using a lithium battery, handle the battery with care. The combustible materials such as lithium or
organic solvent contained in the battery may generate heat, explode, or catch fire, resulting in personal injury
or fire. Read related manuals carefully and handle the lithium battery correctly as instructed.
• When using a POD that has analog switch resolution with resistance film, do not press two or more points on
the screen at the same time. If there is a switch between the two pressed points, it may be activated.
• Take safety precautions during such operations as setting change during running, forced output, start, and
stop. Any misoperation may cause unexpected machine motions, resulting in machine accident or damage.
• In facilities where a failure of POD could lead to accident threatening human life or other serious damage, be
sure that the facilities are equipped with adequate safeguards.
• At the time of disposal, POD must be treated as industrial waste.
• Before touching POD, discharge static electricity from your body by touching grounded metal. Excessive
static electricity may cause malfunction or trouble.
CAUTION