Filter
Top Products
5
Cabinet Width 30” (76.2 cm)
Recommended
Minimum
Cutout Location
from Floor 32 1/2” (82.6 cm)
Cutout Depth 23 1/2” (59.7 cm) Min.
Cutout Width 28 1/2” (72.4 cm) Min.
28 5/8” (72.7 cm) Max.
Cutout Height 27 1/4” (69.2 cm) Min.
27 5/16” (69.2 cm) Max.
If the cabinet does not have a solid bottom,
two braces or runners must be installed
level with the bottom of the cutout to
support the weight of the oven. For single
ovens, the runners and braces must
support 175 lbs. (79 kg).
Installation Instructions
Cutout for Single Built-In Oven
A1
NOTE: If marks, blemishes or the
cutout opening are visible above the
installed oven, it may be necessary to
add wood shims under the runners and
front trim until the marks or opening
are covered.
CUTOUT
HEIGHT
27 1/4" MIN.
27 5/16" MAX.
CUTOUT
WIDTH
28 1/2" MIN.
28 5/8" MAX.
5"
22" TO
BOTTOM OF
JUNCTION BOX
JUNCTION BOX
LOCATION
RECOMMENDED
CUTOUT
LOCATION
32 1/2"
FROM THE
FLOOR
CABINET
WIDTH
30"
ALLOW 11/16" FOR
OVERLAP OF THE
OVEN OVER SIDE
EDGES OF CUTOUT
THE OPENING
BETWEEN INSIDE
WALLS MUST
BE AT LEAST
28 1/2"WIDE
ALLOW 1" FOR
OVERLAP
ON OVEN TOP
AND BOTTOM
OF CUTOUT
21"
ALLOW A MINIMUM
OF 21" FOR CLEARANCE
TO ADJACENT CORNERS,
DRAWERS, WALLS ETC.
WHEN THE DOOR IS OPENED.
Allow 11/16”
(1.75 cm) for
overlap of oven
over side edges
of cutout
Junction Box
Location
Cabinet
Width
30” (76.2 cm)
Allow a minimum
of 21” (53.3 cm) for
clearance to adjacent
corners, drawers,
walls, etc. when
door is open
Cutout
Width
28 1/2” Min.
28 5/8” Max.
(72.4 to
72.7 cm)
22” (55.9 cm)
to Bottom of
Junction Box
5”
(12.7 cm)
Cutout
Height
27 1/4” Min.
27 5/16” Max.
(69.2 to 69.3 cm)
Recommended
minimum cutout
location from
floor 32 1/2” (82.6 cm)
Opening
Between
Inside Walls
Must Be
At Least
28 1/2”
(72.4 cm)
Wide
Allow 1” (2.5 cm)
minimum for
overlap of oven
top and 1
1
⁄
4
”
(3.2 cm) overlap
of oven bottom
of cutout
21”
(53.3 cm)
This oven is not approved for
stackable or side by side installation.
NOTE: If the cabinet does
not have a front frame and
the sides are less than 3/4”
(1.9 cm) thick, shim both
sides equally to establish
the cutout width.
C
L
SUITABLE
BRACING
TO SUPPORT
RUNNERS
2" x 4" or
EQUIVALENT
RUNNERS
21 5/8"
OVER CENTERLINE
OF CABINET
Install a
solid bottom
or 2” x 4”
(5 cm x 10 cm)
or equivalent
runners level
with bottom
of cutout
Suitable
Bracing
to Support
Runners
21 5/8”
(54.9 cm)
Over Centerline
of Cabinet
The solid bottom or runners must be level
with the bottom of the cutout, or the bottom
trim may not install correctly and then
interfere with the door opening.