Filter
Top Products
10
Menu Configuration—MAIN MENU
PICTURE IMPROVEMENT
Setting for the picture quality
Item To do Setting value
APERTURE*
1
Select the frequency of the luminance signal compensated in
“APERTURE LEVEL.”
OFF, LOW, HIGH
APERTURE
LEVEL*
1
Compensate the frequency response of the luminance signal of the
video signal.
01 – 10
sub menu
Display the sub menu which enables you to adjust the items of “PICTURE IMPROVEMENT” while
viewing the actual picture.
reset
Restore the default settings for all the items in “PICTURE IMPROVEMENT.”
• When the FOCUS lamp lights, “PICTURE IMPROVEMENT” does not appear on the menu (☞ r on page 6).
BACK LIGHT
Adjusts the brightness of the display.
• When the DYNAMIC lamp lights, this item does not appear on the menu (☞ t on page 6).
COLOR RANGE MODE
Reduces the difference of the luminance level specific to the LCD panel.
• When “ON” is selected, the color temperature becomes the innate temperature in the LCD panel, and the
setting of “WHITE BALANCE SET.” becomes ineffective (☞ page 12).
VIDEO/COMPO. SEL.
Selects the signal type you want to use for the VIDEO/COMPONENT terminals.
• When select the component (COMPO.), make sure to set the component level in “COMPO. LEVEL” in
“PICTURE SUB ADJ.” (☞ page 12).
ASPECT*
1
Changes the aspect ratio of the picture.
AREA MARKER*
1
Setting for area marker functions
Item To do Setting value
MARKER SELECT*
2
Select the style of the area marker.
☞ “NOTE”
ASPECT SELECT*
2
Select the aspect ratio of the area marker. 4:3, 14:9, 13:9
SAFETY MARKER
Adjust the area of the safety marker. OFF, 80% – 100%
R-MARKER SELECT*
2
Select the style of the area marker.
☞ “NOTE”
R-ASPECT SELECT*
2
Select the aspect ratio of the area marker. 4:3, 14:9, 13:9
R-SAFETY MARKER
Adjust the area of the safety marker. OFF, 80% – 100%
• The area marker or the safety marker is displayed by using A. MARKER or S. MARKER button, or external
control.
• Select either non-“R-” items or “R-” items to activate by using external control (☞ “External Control” on page
14).
• When a picture is displayed in 4:3 aspect ratio, the safety marker for the 4:3 area is displayed.
• To display the safety marker for the area of a picture displayed in 16:9 aspect ratio, hide the area marker.
*
1
Memorized for each input — composite signal input (VIDEO), component signal input (COMPO.), and SDI signal input.
*
2
Displayed only when the picture is displayed in 16:9 aspect ratio.
Operation guide
Shows the buttons for
each operation.
For the operation procedure, see page 7.
Setting value: –20 – +20
Setting value: VIDEO, COMPO. (component)
• The menu automatically disappears in about 30 seconds after the previous operation.
• Some items may not appear on the menu depending on the input or the input signal.
• The items controlled by the MAKE system do not appear on the menu.
Setting value: OFF, ON
Setting value: 4:3, 16:9
Setting of “MARKER SELECT” and “R-MARKER SELECT”
The setting values and features are as follows.
OFF: “MARKER SELECT” and “R-MARKER SELECT” do not function.
LINE: Displays the area with an outline.
HALF: The area outside the specified aspect ratio of the screen is displayed as 50% transparency.
HALF+L: The area of the specified aspect ratio of the screen is indicated by an outline, and the area outside
of that is displayed as 50% transparency.
BLK.: The area outside the specified aspect ratio of the screen is black. Only the portion of the picture within
the designated area is displayed.
BLK. +L: The area of the specified aspect ratio of the screen is indicated by an outline, and the area outside
of that becomes black so that only the area inside the line is displayed.
NOTE
DT-V9L1D_EA_EN_R.indd 10DT-V9L1D_EA_EN_R.indd 10 07.9.14 6:19:25 PM07.9.14 6:19:25 PM