Filter
Top Products
108
FAX machines, to send any
message unless said
message clearly contains in
a margin at the top or bottom
of each transmitted page or
on the first page of the
transmission, the date and
time it is sent and an
identification of the business
or other entity, or other
individual sending the
message, and the telephone
number of the sending
machine or such business,
other entity, or individual.
(The telephone number
provided may not be a 900
number or any other number
for which charges exceed
local or long-distance
transmission charges.)
See the section in this
publication entitled
Personalize Fax, on page 12,
in order to program this
information into your fax
machine.
Notice to users of the
Canadian telephone
network
This product meets the
applicable Industry Canada
technical specifications.
The Ringer Equivalence
Number (REN) is an
indication of the maximum
number of terminals allowed
to be connected to a
telephone interface. The
terminus of an interface may
consist of any combination of
devices, subject only to the
requirement that the sum of
the Ringer Equivalence
Numbers of all the devices
does not exceed five. The
modem REN is located on
the rear of the equipment on
the product labeling.
Telephone companies report
that electrical surges,
typically lightning transients,
are very destructive to
customer terminal
equipment connected to AC
power sources. This has
been identified as a major
nationwide problem. It is
recommended that the
customer install an AC surge
arrestor in the AC outlet to
which this device is
connected. This is to avoid
damage to the equipment
caused by local lightning
strikes and other electrical
surges.
This equipment uses CA11A
telephone jacks.
Using the X6100 Series
All-In-One in Germany
The X6100 Series All-In-One
requires a German billing
tone filter (Lexmark part
number 14B5123) to be
installed on any line which
receives metering pulses in
Germany. Metering pulses
may or may not be present
on analog lines in Germany.
The subscriber may request
that metering pulses be
placed on the line, or can
have them removed by
calling the German network
provider. Normally, metering
pulses are not provided
unless specifically requested
by the subscriber at the time
of installation.
Using the X6100 Series
All-In-One in
Switzerland
The X6100 Series All-In-One
requires a Swiss billing tone
filter (Lexmark part number
14B5109) to be installed on
any line which receives
metering pulses in
Switzerland. The Lexmark
filter must be used, as
metering pulses are present
on all analog telephone lines
in Switzerland.
The Lexmark X6100 Series
has been tested and found to
comply with the limits for a
Class B digital device,
pursuant to Part 15 of the
FCC Rules. Operation is
subject to the following two
conditions: (1) this device
may not cause harmful
interference, and (2) this
device must accept any
interference received,
including interference that
may cause undesired
operation.
The FCC Class B limits are
designed to provide
reasonable protection
against harmful interference
in a residential installation.
This equipment generates,
uses and can radiate radio
frequency energy and, if not
installed and used in
accordance with the
instructions, may cause
harmful interference to radio
communications. However,
there is no guarantee that
interference will not occur in
a particular installation. If this
equipment does cause
harmful interference to radio
or television reception, which
can be determined by turning
the equipment off and on, the
user is encouraged to try to
correct the interference by
one or more of the following
measures:
• Reorient or relocate the
receiving antenna.
• Increase the separation
between the equipment
and receiver.
• Connect the equipment
into an outlet on a circuit
different from that to
which the receiver is
connected.
• Consult your point of
purchase or service
representative for
additional suggestions.
The manufacturer is not
responsible for any radio or
television interference
caused by using other than
recommended cables or by
unauthorized changes or
modifications to this
equipment. Unauthorized
changes or modifications
could void the user's
authority to operate this
equipment.
Note:To assu re
compliance with FCC
regulations on
electromagnetic
interference for a Class B