Filter
Top Products
ENGLISH-5
Preparation
4-ENGLISH
Contents
Preparation
IMPORTANT SAFETY NOTICE ...2
Precautions with regard to
safety .........................................6
Accessories ...............................10
Before use ..................................11
Location and function of each
part...........................................13
Getting started
Setting-up...................................18
Projection methods, Projector
position, Projection distances,
Setting up range using the lens shift
function
Connections...............................22
Connecting to video equipment,
Connecting to equipment
compatible with HDMI,
Connecting to computer
Preparation for the remote
control unit..............................25
Basic operation
Turning on the power................26
Turning off the power................28
Useful functions
Setting the aspect ratio.............30
Selecting the picture mode.......33
Turning on the button lights.....33
Retrieving the saved picture
settings....................................34
Turning off the picture momentarily
...34
Displaying the “PICTURE” menu
.....35
Displaying the “ADVANCED MENU”
...35
Using the colour management function
...36
Adjustments and settings
On-screen menus ......................40
Menu screens, Menu operation
guide, Returning a setting to the
factory default
Adjusting the picture.................44
PICTURE MODE, CONTRAST,
BRIGHT, COLOUR, TINT,
SHARPNESS, COLOUR TEMP.,
DYNAMIC IRIS, Noise
Reduction(NR), CINEMA REALITY,
TV-SYSTEM, ADVANCED MENU,
MEMORY SAVE, MEMORY LOAD,
SIGNAL MODE,
Projecting sRGB-
compatible pictures
Adjusting the position...............48
Horizontal position, Vertical position,
DOT CLOCK, CLOCK PHASE,
ASPECT, WSS, OVER SCAN,
KEYSTONE, AUTO SETUP
Changing the display language
...50
Option settings ..........................51
OSD, OSD DESIGN, OSD
POSITION, AUTO SEARCH, BACK
COLOUR, STARTUP LOGO,
DESK/CEILING, FRONT/REAR,
OFF TIMER, FAN CONTROL,
LAMP POWER, LAMP RUNTIME
Care and maintenance
When the TEMP indicator and the
LAMP indicator are illuminated
...54
Cleaning and replacing
the air filter..............................56
Replacing the lamp unit............57
Before calling for service..........60
Cleaning and maintenance.......61
Others
Specifications ............................62
Appendix ....................................64
List of compatible signals, General
arrangement of the COLOUR
MANAGEMENT menu, Using the
SERIAL connector, Projection
dimensions calculation methods
Dimensions ................................69
Trademark acknowledgements
...70
IMPORTANT: THE MOULDED PLUG (U.K. only)
FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT
CAREFULLY.
This appliance is supplied with a moulded three pin mains plug for your
safety and convenience. A 13 amp fuse is fitted in this plug. Should the fuse
need to be replaced, please ensure that the replacement fuse has a rating of
13 amps and that it is approved by ASTA or BSI to BS1362.
Check for the ASTA mark or the BSI mark on the body of the fuse.
If the plug contains a removable fuse cover, you must ensure that it is refitted
when the fuse is replaced. If you lose the fuse cover, the plug must not be
used until a replacement cover is obtained. A replacement fuse cover can be
purchased from an Authorised Service Centre.
If the fitted moulded plug is unsuitable for the mains socket in your
home, then the fuse should be removed and the plug cut off and
disposed of safely. There is a danger of severe electrical shock if the
cut off plug is inserted into any 13 amp socket.
If a new plug is to be fitted, please observe the wiring code as shown below.
If in any doubt, please consult a qualified electrician.
WARNING: — THIS APPLIANCE MUST BE EARTHED.
IMPORTANT: — The wires in this mains lead are coloured in accordance
with the following code: —
Green-and-Yellow: Earth
Blue: Neutral
Brown: Live
As the colours of the wire in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in your plug,
proceed as follows.
The wire which is coloured GREEN-AND-YELLOW must be connected
to the terminal in the plug which is marked with the letter E or by the
Earth symbol or coloured GREEN or GREEN-AND-YELLOW.
The wire which is coloured BLUE must be connected to the terminal in
the plug which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal
in the plug which is marked with the letter L or coloured RED.
How to replace the fuse: Open the fuse
compartment with a screwdriver and replace the
fuse.
ASA
13A250V
BS1363/A
HE-8
N
ASA
L
FUSE