Filter
Top Products
43
1.3 INDUSTRY CANADA NOTICE
The Canadian Department of Communications label identifies cer-
tified equipment. This certification means that the equipment meets
certain telecommunications network protective, operational and safety
requirements. The Department does not guarantee the equipment will
operate to the user's satisfaction. Before installing this equipment,
users should ensure that it is permissible to be connected to the facili-
ties of the local telecommunications company. The equipment must
also be installed using an acceptable method of connection. In some
cases, the company’s inside wiring associated with a single line individ-
ual service may be extended by means of a certified connector assem-
bly (telephone extension cord). The customer should be aware that
compliance with the above condition may not prevent degradation of
service in some situations. Repairs to some certified equipment should
be made by an authorized maintenance facility designated by the sup-
plier. Any repairs or alterations made by the user to this equipment, or
equipment malfunctions, may give the telecommunications company
cause to request the user to disconnect the equipment. Users should
ensure for their own protection that the ground connections of the
power utility, telephone lines and internal metallic water pipe system,
are connected together. This protection may be particularly important
in rural areas.
1.4 FCC INFORMATION
The Model 2720 Series has been tested and registered in compli-
ance with the specifications in Part 68 of the FCC rules. A label on the
equipment bears the FCC registration number. You may be requested
to provide this information to your telephone company.Your telephone
company may make changes in its facilities, equipment, operations or
procedures that could affect the proper operation of the Model 2720
Series. If this happens, the telephone company should give you
advance notice to prevent the interruption of your service. The tele-
phone company may decide to temporarily discontinue your service if
they believe your Model 2720 Series may cause harm to the telephone
network. Whenever possible, they will contact you in advance. If you
elect to do so, you have the right to file a complaint with the FCC. If
you have any trouble operating the Model 2720 Series, please contact
Patton Electronics Technical Support 301-975-1000. The telephone
company may ask you to disconnect the equipment from the telephone
network until the problem has been corrected or until you are certain
that the Model 2720 Series is not malfunctioning. In accordance with
FCC rules and regulation CFR 47 68.218(b)(6), you must notify the
telephone company prior to disconnection. The following information
may be required when applying to your local telephone company for
leased line facilities. The Universal Service Order Code (USOC) is
RJ48. The Facility Interface Codes (FIC) are 04DU9-BN, 04DU9-DN,
04DU9-1KN, and 04DU9-1SN. The Service Order Code (SOC) is 6.0N.
1.5 FCC PART 68 COMPLIANCE STATEMENT
This equipment complies with Part 68 of FCC Rules. Please note the
following:
1. You are required to request serivce from the telephone company
before you connnect the CSU to a network. When you request serivce,
you must provide the telephone company with the following data. When
you request T1 Service, you must provide the telephone company with
the Facility Interface Code. Provide the telephone company with both of
the following codes: 04DU9-B (1.544 MB D4 framing format) and
04DU9-C (1.544 MB ESF format). The telephone company will select
the code it has available. The Service Order Code(s) (SOC): 6.0N. The
required Universal Service Order Code (USOC) jack: RJ 48C. The
make, model number, and FCC Registration number of the CSU.
2. Your telephone company may make changes to its facilities, equip-
ment, operations, or procedures that could affect the proper functioning
of your equipment. The telephone company will notify you in advance
of such changes to give you and opportunity to maintain uninterrupted
telephone service.
CAUTION: Users should not attempt to make such connections
themselves, but should contact the appropriate electric inspection
authority, or electrician, as appropriate.
Facility
Interface Service Network
Service Code Code Connection
1.544 Mbps SF format without line power 04DU9-BN 6.0N RJ48C
1.544 Mbps SF and B8ZS without line power 04DU9-DN 6.0N RJ48C
1.544 Mbps ANSI ESF without line power 04DU9-1KN 6.0N RJ48C
1.544 Mbps ANSI ESF and B8ZS w/o line power 04DU9-1SN 6.0N RJ48C