Filter
Top Products
28
Special Features
voice channel or during trunking delay
time. Therefore the priority check seems
random during peak hours. Do not over-
estimate the priority check during trunk-
ing operation.
• If you program a weather channel as the
priority channel, the scanner stays in the
priority channel only when the scanner
detects the weather alert tone.
To program a frequency in the priority chan-
nel:
1. Press
MAN
.
2. Use the number keys to enter the chan-
nel number which contains the fre-
quency you want to program as the
priority channel. Then press
MAN
again.
3. Press
FUNC
then
PRI
.
,
,,
,I@ý á
I@ý áI@ý á
I@ý á?8EE<C
?8EE<C?8EE<C
?8EE<C
blinks on the bottom line.
To program the priority channel directly:
1. Press
PROG
.
2. Press
PRI
.
3. Enter the desired frequency, then press
ENTER
.
Note:
This scanner cannot set a channel as
the priority channel if the channel's receive
mode is MOT or ED.
To program a weather channel as the priority
channel:
1. Press
WX
.
2. Select the weather channel you want to
program as the priority channel.
3. Press
FUNC
then
PRI
.
,
,,
,I@ý á
I@ý áI@ý á
I@ý á?8EE<C
?8EE<C?8EE<C
?8EE<C
flashes on the bottom line two times.
To turn on the priority feature, press
PRI
so
,
,,
,
appears on the top line while in scanning
mode.
,
,,
,.%F
.%F.%F
.%FE
EE
E
(or
,.%NO
,.%NO,.%NO
,.%NO
if you set the priority
to a weather frequency) appears on the bot-
tom line. If the scanner detects activity on the
priority channel,
,
,,
,I@ý á
I@ýáI@ýá
I@ýá?8EE<C
?8EE<C?8EE<C
?8EE<C
appears for 3
seconds. Or if the scanner detects a weather
alert tone in Priority WX mode,
,
,,
,I@ýá
I@ýáI@ýá
I@ýá?8EE<C
?8EE<C?8EE<C
?8EE<C
appears for 3 seconds then changes to
3<8K?<Iýã(!.0
3<8K?<Iýã(!.03<8K?<Iýã(!.0
3<8K?<Iýã(!.0
and the scanner sounds an
alert. The scanner sounds the alert for five
minutes when it receives the weather alert
signal. After five minutes the alert stops and
the scanner beeps every ten seconds. Press
any key to stop the sound. The scanner is
ready to receive a new signal.
Notes:
• Priority WX is only for receiving a
weather alert.
• When the scanner detects a 1050 Hz
alert tone, priority WX activates and you
hear a weather alert.
• If you program a weather frequency into
the priority channel and the scanner
detects a weather alert tone on that fre-
quency, the scanner sounds the alert
tone.
To turn off the priority feature, press
PRI
.
CHANGING THE RECEIVE
MODE
The scanner is preset to the most common
AM or FM receive mode for each frequency
range. The preset mode is correct in most
cases. However, some amateur radio trans-
missions and trunked systems do not oper-
ate in the preset mode. If you try to listen to a
transmission when the scanner is not set to
the correct receive mode, the transmission
might sound weak or distorted.
If you want to listen to trunking transmissions
in closed mode, you might have to change
the receive mode.