Samsung CLX-6200ND All in One Printer User Manual


 
52 _Faxing
Sending a fax automatically
1. Press
Fax
.
2. Load originals face up into the DADF (or ADF), or place a single original
face down on the scanner glass.
For details about loading an original, see page 32.
Ready to Fax appears on the top line of the display.
3. Adjust the resolution and the darkness to suit your fax needs.
4. Enter the receiving fax machine’s number.
You can use speed buttons, speed dial numbers, or group dial numbers.
For details about storing and searching for a number, see page 57.
5. Press Color Start or Black Start.
6. If an original is placed on the scanner glass, select Yes to add another
page. Load another original and press OK.
7. When you have finished, select No at the Another Page? prompt.
After the number is dialed, the machine begins sending the fax when the
receiving fax machine answers.
Sending a fax manually
1. Press
Fax
.
2. Load originals face up into the DADF (or ADF), or place a single original
face down on the scanner glass.
For details about loading an original, see page 32.
3. Adjust the resolution and the darkness to suit your fax needs. See page
51.
4. Press On Hook Dial. You hear a dial tone.
5. Enter the receiving fax machine’s number.
You can use speed buttons, speed dial numbers, or group dial numbers.
For details about storing and searching for a number, see page 57.
6. Press Color Start or Black Start when you hear a high-pitched fax
signal from the remote fax machine.
Confirming a transmission
When the last page of your original has been sent successfully, the machine
beeps and returns to ready mode.
When something goes wrong while sending your fax, an error message
appears on the display. For a list of error messages and their meanings, see
page 78. If you receive an error message, press Stop/Clear to clear the
message and try to send the fax again.
You can set your machine to print a confirmation report automatically each
time sending a fax is completed. For further details, see page 56.
Automatic redialing
When the number you have dialed is busy or there is no answer when you
send a fax, the machine automatically redials the number every three
minutes, up to seven times according to the factory default settings.
When the display shows Retry Redial?, press OK to redial the number
without waiting. To cancel the automatic redialing, press Stop/Clear.
To change the time interval between redials and the number of redial
attempts. See page 56.
Redialing the last number
To redial the number you called last:
1. Press Redial/Pause.
2. When an original is loaded in the DADF (or ADF), the machine
automatically begins to send.
If an original is placed on the scanner glass, select Yes to add another
page. Load another original and press
OK
. When you have finished,
select No at the
Another Page?
prompt.
Sending faxes on both sides of paper
You can set the machine to send faxes on both sides of paper. (CLX-
6210FX, CLX-6240FX only)
1. Press
Fax
.
2. Press Duplex.
3. Press the left/right arrow until the binding option you want appears.
Off: Send faxes in Normal mode.
•2 Side: Send faxes on both sides of the original.
2 ->1Side ROT2: Send faxes on both sides of the original and prints
each one on a separate sheet, but the information on the back side
of the printout is rotated 180°.
4. Press OK to save your selection.
If the mode is enabled, the Duplex button is backlit.
RECEIVING A FAX
Selecting the paper tray
After loading the print media for fax output, you have to select the paper tray
you will use for the fax reception.
1. Press Menu () until System Setup appears on the bottom line of the
display and press
OK
.
2. Press the left/right arrow until Paper Setup appears and press
OK
.
3. Press the left/right arrow until Paper Source appears and press
OK
.
4. Press the left/right arrow until Fax Tray appears and press
OK
.
5. Press the left/right arrow until the paper tray you want appears and
press
OK
.
6. Press Stop/Clear to return to ready mode.
Changing receiving modes
1. Press Fax.
2. Press Menu () until Fax Setup appears on the bottom line of the
display and press
OK
.
3. Press the left/right arrow until Receiving appears and press
OK
.
4. Press
OK
when Receive Mode appears.
5. Press the left/right arrow until the fax reception mode you want appears.
•In Fax mode, the machine answers an incoming fax call and
immediately goes into the fax reception mode.
•In Tel mode, you can receive a fax by pressing On Hook Dial and
then Color Start or Black Start. You can also pick up the handset of
the extension phone and then press the remote receive code. See
page 53.
•In Ans/Fax mode, an answering machine attached to your machine
answers an incoming call, and the caller can leave a message on the
answering machine. If the fax machine senses a fax tone on the line,
the machine automatically switches to Fax mode to receive the fax.
See page 53.
•In DRPD mode, you can receive a call using the Distinctive Ring
When you want to cancel a fax job, press Stop/Clear at any time while
sending.
When you want to cancel a fax job, press Stop/Clear at any time while
sending.