Filter
Top Products
Trango Broadband Wireless — User Manual M2400S Rev. A
Page
42
Command Radio Description Access
22. Remarks
23. RF TX retry at AP, RF TX retry maxed out at AP
RF TX retry at SU, RF TX retry maxed out at SU
su ipconfig <suid> <new IP> <new
subnet> <new gateway>
AP Change IP, subnet, gateway for specified SU rw
su linktest <suid> AP Perform linktest for specified SU ro/rw
su ping <suid> AP Request SU’s ranging and RSSI information ro/rw
su reboot <all | suid> AP Reboot a specific SU or all SUs rw
su sw <suid> <sw #> <on | off> AP Change switch settings on specified SU rw
sudb add <suid> <pr|re> <mac> AP Add new SU to SUDB rw
sudb cirmir <<suid>|all> <cir dn> <cir up>
<mir dn> <mir up>
AP Change SU’s CIR/MIR settings rw
sudb defaultcirmir AP Display default CIR and MIR in SUDB ro/rw
sudb defaultcirmir <cir_dn, 0..3000> <cir_up,
0..3000> <mir_dn, 0..3000> <mir_up, 0..3000>
AP Change default CIR and MIR rw
sudb defaultcirmir <default cir dn> <default cir
up> <default mir dn> <default mir up>
AP Set MIR/CIR values to default values rw
sudb delete <suid | all> AP Delete SU in SUDB rw
sudb dload AP Download SUDB file from TFTP buffer and write to flash memory.
This command is used to load a text file that contains the SUDB into
the AP. This command can be useful if there are large numbers of
SUs in the sector.
rw
sudb gid <suid | all> <0..15> AP Change SU’s gid rw
sudb view AP Display all SUDB ro/rw
survey <search time, sec> <antenna, h | v | e> AP/SU Spectrum analysis of the entire band (and near band)
<search time> = 1..10 sec per channel
Opmode “OFF” only
ro/rw
Sw AP/SU Display current sw setting ro/rw
sw 0 [<on | off>] AP/SU set sw #0 – enable or disable packet filter for broadcast/ multicast
packets
on = filtering
default = on
rw
sw 1 [<on | off>] SU Enable or disable SU’s autoscan AP feature
If on, SU will automatically scan each channel and antenna port
searching for AP.
default=on
rw
sw 2 [<on | off>] SU Enable or disable SU’s TCP/IP service for AP
Allows TCP/IP access to SU from AP side of network via wireless
link.
default = on
rw
sw 3 [<on | off>] AP Enable or disable SU to SU (peer to peer) service
default = off
rw
sw 5 [<on | off>] AP/SU Enable or disable HTTPD (browser interface)
default = on
rw
sw 6 [<on | off>] SU Enable or disable TCP/IP service for Ethernet port while SU is in
Opmode “ON”
default = on
rw
sw 7 [<on | off>] AP Enable or disable TCP/IP service for SU. Allows TCP/IP access to
AP from SU side of network via wireless link.
default = on
rw
sysinfo AP/SU Display system configuration ro/rw
targetap SU Display the SU current setting for target AP ro/rw
targetap all SU SU will associate with any AP with the same Base ID
“all” is the default setting.
rw
targetap only <mac1, hex> [<mac2, hex>] SU SU will only associate with AP with specified MAC addresses. rw
targetrssi AP Display SU Target RSSI in dBm. This setting is used in the SU
power leveling process.
ro/rw
targetrssi <dBm, -90..-50> AP Change target RSSI. Note: Target RSSI must be +5 dB more than
rfrxth (RFRX Threshold).
rw