Filter
Top Products
1.3.2.5 Sync Signal Loading
TTL input loading shall be equivalent to one TTL
input load. When logic 0 is asserted by a sync
input , the maximum current source from any
single monitor sync input to the driver is 1.6 mA
.When logic 1 is asserted , the maximum current
source from the driver to any single monitor sync
input is 400 uA .
1.3.2.6 Abnormal Signal Immunity
The monitor shall not be damaged by improper
sync timing , pulse duration , or absence of sync ,
or abnormal input signal amplitude ( video and/ or
sync too large or too small) , or any other
anomalous behavior of a graphics card video
generator when changing modes , or when any
combination of input signals is removed or replaced
. Additionally , under these conditions , the monitor
shall not cause damage to the driving source
1.3.3 User Controls and Indicators
1.3.3.1 Power On / Off Switch
The monitor shall have a power control switch
visible and accessible on the front of the monitor .
The switch shall be marked with icons per IEC 417
, # 5007 and # 5009.The switch shall interrupt the
DC supply to the monitor
1.3.3.2 Power Indicator LED
The monitor shall make use of an LED type
indicator located on the front of the monitor .
The LED color shall indicate the power states as
given in Table 1.
1.3.4 Monitor Modes and Timing Capability
1.3.4.1 Format and Timing
The monitor shall synchronize with any vertical
frequency from 56 to 75 Hz , and with any
horizontal frequency from 31 to 83KHz. If the input
frequency is out of the above – specified range,
the monitor shall display a warning screen
indicating that the input frequency is out of range.
Under no circumstances shall any combination of
input signals cause any damage to the monitor .
1.3.4.2 Factory Assigned Display Modes
There are 21 factory pre-set frequency video
modes. These modes have a factory pre-set for all
characteristics affecting front-of-screen
performance. When the system is powered-
on,previously stored screen parameters for a pre-
defined mode will be recalled if the operating
mode is one of those stored in memory. If the
operating mode is not one of those stored in
memory, the monitor CPU will select the PRESET
timing for a mode that is the next lowest in
horizontal scanning frequency to the mode being
currently used. The screen parameters may be
adjusted by the use of the front bezel controls and
then may be saved as a user defined mode. The
monitor shall include all the preset video timings
shown in the following page.(Please see Note.(3) )
1.3.3.4 OSD adjustment
1. Product Specification (continued)
Function LED Color
FullPower Blue color
Sleep Orange color
Table 1
1.3.3.3 On-Screen Display
The Lite-ON On Screen Display system shall be
used , controlled by a Menu button. If the buttons
remain untouched for OSD turn off time while
displaying a menu , the firmware shall save the
current adjustments and exit. Also, if the video
controller changes video mode while the OSD is
active, the current settings shall be saved
immediately, the OSD turn off, and new video mode
is displayed.
Key When no OSD display OSD Displayed
1.To display the OSD menu on the screen.
2.ToselecttheOSD sub-Menu
>
Speaker Volume/Minus
(withAudio)
1.Forward selection of the OSD menu.
2.Increase the value after sub-menu selected.
<
Speaker Volume/Plus
(withAudio)
1.Back-forward selection of the OSD menu.
2.Decrease the value after sub-menu selected.
E
Empowering Menuorsub.menuEXIT/Scenariomode
Description
MENU
Menu Display
Menu orsub.menuEXIT/AutoAdjustfunction.
Auto
Auto Adjust Function
ITEM CONTENT
AUDIO VOLUME To increase ordecrease the sound level
BRIGHTNESS Back light Luminance ofthe LCD panel is adjusted.
CONTRAST A gain of R , G and B signal isadjusted.
AUTO CONTRAST A gain of R , G and Bsignal auto adjust.
CLOCK The ratioof dividing frequency of the dotclock is adjusted.
PHASE The phase ofthe dot clockis adjusted.
H-POSITION The indication screen is horizontally moved right and left (1 Pixels pitch).
V-POSITION The indication screen is vertically moved up and down (1 Pixels pitch).
AUTO ADJUST Clock system autoadjustment, about under8 sec.
COLOR BALANCE Select three kinds ofmodes. (USER /6500 /9300 ).
OSD POSITION The OSD indication position can beadjusted.
OSD LANGUAGE
Select the language used for the OSD menu among English ,French ,
Italian , Deutsch and Spanish.
RECALL DEFAULTS All data copy from factory shipmentdata.
OSD DURATION Adjust OSD menu offtime range from10~120 second.
POWER-SAVE
Back lightof the LCD panel is cutwhen the signal is notinput (AC line
power consumption 2W or less).
INFORMATION
The frequency ofthe horizontal/ vertical synchronizing signal underthe
input isindicated.
※
NOTE : OSD MENU SEE APPENDIX A
4
Go to cover page
ACER X193HQ