Filter
Top Products
1. Product Specification (continued)
1.3.1.3 Audio Jack (option)
This jack shall connect the audio input from
host computer.
1.3.2 Video Input Signals
Video Input Signal Ranges
1.3.2.1 Video Signal Amplitudes
The three video inputs consist of Red ,Green , and Blue
signals, each with its own coaxial cable terminated at the
monitor. These video signals are analog levels, where 0
V corresponds to black , and 700 mV is the maximum
signal amplitude for the respective color, when each
signal is terminated by a nominal 75.0 ohms .For a given
monitor luminance levels are measured using this
defined video amplitud driving a monitor meeting the
termination requirements .The signal amplitude is not to
be readjusted to compensate for variations in termination
impedance.
1.3.2.2 Video Signal Termination Impedance
This analog video signal termination shall be 75 1%
which shall be resistive with a negligible reactive
component
1.3.2.3 Synchronization ( Sync ) Signals
The Horizontal Sync (HS) TTL signal is used to initiate
the display of a horizontal line. HS may be either active
high or active low, depending upon the timing .The
Vertical Sync (VS) TTL signal is used to initiate the
display of a new frame .VS may be either active high or
active low, depending on the timing
1.3.2.4 Sync Signal Levels
The monitor must accept sync signals from both 3.3 and
5 volt TTL logic families.The inputs shall sense a logic 0
when the input is 0.8 volt or less and shall sense a logic
1 when the input is 2.0 volts or greater. In addition to
these level requirements, there shall also be a minimum
of 0.3 volt hysteresis provided for noise immunity
(typically by using a Schmitt Trigger input ).That is , the
input level at which the monitor actually detects a logic 0
shall be at least 0.3 volt lower than the level at which it
actually detects a logic 1.If the monitor sync processing
circuits are designed around the 3.3 volt logic family
,then the sync inputs must be 5 volt tolerant .
Ω+/-
.
DVI-I/DVI-D(If using DVI-D cable,C1,C2,C3,C4,C5 is NC)
Note 1) Schmitt-Triggers Input, Supported 3.3V device
H(&V) sync output from PC
No. Symbol Item Min
Normal
Max Unit Remark
1
Fh Scanning Horizontal Frequency 30 94 kHz Minimum range
2
Fv Scanning Vertical Frequency 55 76 Hz Minimum range
3
Vih HiLevelInput 2 5 Note 1)
4
Vil Low Level Input 0 0.8 V Note 1)
5
Video RGB Analog Video Level 0.0 0.7 1.0 V
75
Ω
to Ground
Note 1) Schmitt-Triggers Input , Supported 3.3V device H(&V) sync outputfromPC.
Video Input Signal
Pin Signal Pin Signal Pin Signal
1
Red-Video
6
Red-GND
11
NC
2
Green-Video
7
Green-GND
12
DDC-SDA
3
Blue-Video
8
Blue-GND
13
H-SYNC
4
NC
9
+5V
14
V-SYNC
5
Connection Detect
10
GND
15
DDC-SCL
Pin Name Description
1 Red-Video Red video signalinput
2 Green-Video Green video signalinput
3 Blue-Video Blue video signalinput
4 NC Not connect
5 ConnectionDetect DeteckVGA Cable have Connected or not
6 Red-GND Analog signalground forthe Redvideo
7 Green-GND Analogsignal ground for the Green video
8 Blue-GND Analog signal ground for the Blue video
9 +5V +5Vinputfrom hostsystem forthe VESA DDC 2Bi function
10 Sync-GND Signalground
11 NC Notconnect
12 NCDDC-SDA SDA signalinputfor theVESA DDC 2Bifunction
13 H-SYNC Horizontalsignalinput from thehost system
14 V-SYNC Vertical signalinput from thehost system
15 DDC-SCL SCL signalinput for the VESA DDC 2Bi function
Connector Pin Description
D-SUB Description
Pin Signal Pin Signal Pin Signal
1RX2- 13NC C1AnalogRed(NC)
2 RX2+ 14 5V C2 Analog Green (NC)
3 GND 15 DVIConnect C3 Analog Blue (NC)
4NC 16HP C4AnalogH-Sync(NC)
5 NC 17 RX0- C5 GND
6 SCL 18 RX0+
7 SCA 19 GND
8AnalogV-Sync(NC) 20NC
9RX1- 21NC
10 RX1+ 22 GND
11 GND 23 RXC+
12 NC 24 RXC-
DVI-I/DVI-D Connector Pin Description
Pin Name Desription
Pi
n Name Desription
1 RX2- TMDS link #0 channel #2 differential pair 16 HP Hot plugging
2 RX2+ TMDS link #0 channel #3 differential pair 17 RX0- TMDS link #0 change #1 differential pair
3 GND GNDfor no link share 18RX0+ TMDS link #0 change #1 differential pair
4 NC NC 19 GND GND for no link share
5NC NC 20NC NC
6 SCL Clock line forDDC interface 21 NC NC
7 SDA Data line for DDC interface 22 GND Clock shield
8 Analog V-Sync V-sync for analog interface 23 RXC+ TMDS clock differentialpair
9 RX1- TMDS link #0 change #1 differential pair 24 RXC- TMDS clock differential pair
10 RX1+ TMDSlink #0 change #1 differential pair C1Analog Red Analog Red signal
11 GND GND for no link share C2Analog Green Analog Green signal
12 NC NC C3Analog Blue Analog Bluesignal
13 NC NC C4 Analog H-Sync H-Sync for analog interface
14 5V +5V input from host system for DDC 2B function C5Analog GND Analog GND
15 DVIConnect Using as Detect Cable
No. Symbol Item Min Normal Max Unit Remark
1 Fh Horizontal Frequency 31 83 kHz Minimum range
2 Fv Vertical Frequency 56 75 Hz Minimum range
3 Vih Hi Level Input 2.0 5.0 V Note 1)
4 Vil Low LevelInput 0 0.8 V Note 1)
5Video
RGB Analog Video
Level 0.0 0.7 0.1 V 75Ω to Ground
Go to cover page
3
ACER X193HQ