Asus P2B-D2 Computer Hardware User Manual


 
ASUS P2B-D2 User’s Manual 11
III. INSTALLATION
Jumpers
1) CLRTC p. 13 Clear Real Time Clock (RTC) RAM
2) 960SEL p.13 i960 Setting (I2O/Bridge)
3) DRAMRAS p.13 i960RD DRAM RAS Setting (Single/Double)
4) FS0, FS1, FS2 p. 14 CPU Bus Frequency
5) BF0, BF1, BF2, BF3 p. 14 CPU Core:Bus Frequency Multiple
6) JP1601 p. 15 Chassis Intrusion Sensor Setting (Enable/Disable)
7) LAN_EN p. 15 LAN Setting (Enable/Disable)
8) SCSI_EN p. 15 SCSI Setting (Enable/Disable)
Expansion Slots/Sockets
1) DIMM1-4 p.16 DIMM System Memory Sockets
2) I-SIMM1, I-SIMM2 p. 18 SIMM i960 Memory Sockets
3) SEC CPU Slots p. 19 Single Edge Contact CPU Support
4) SLOT1 p. 24 16-bit ISA Bus Expansion Slot
*
5) S-PCI1, S-PCI2, S-PCI3 p. 25 32-bit Secondary PCI Bus Expansion Slots
6) PCI1, PCI2, PCI3 p. 25 32-bit PCI Bus Expansion Slots
Hardware Monitor
1) J1601, J1602 p. 20 CPU Heat Sensor Connector
Connectors
1) PS2KBMS p. 26 PS/2 Keyboard Port Connector (6 pin female)
2) PS2KBMS p. 26 PS/2 Mouse Port Connector (6 pin female)
3) PRINTER p. 27 Parallel (Printer) Port Connector (25 pin female)
4) COM1 p. 27 Serial Port COM1 Port Connector (two 9 pin male)
5) VGA p. 27 Monitor (VGA) Output Port Connector (15 pin female)
6) USB p.28 Universal Serial BUS Ports 1 & 2 (two 4 pin female)
7) RJ-45 p.28 RJ-45 Port Connector (8 pin female)
8) IDELED p. 28 IDE/SCSI LED Activity Light (2 pins)
9) IDE1, IDE2 p. 29 Primary/Secondary IDE Connector (40 pins)
10) CHASSIS p. 29 Chassis Intrusion Sensor Lead (4-1 pins)
11) IR p. 30 Infrared Port Module Connector (5 pins)
12) CHA_/CPU_/PWR_FAN p. 30 Chassis/CPU/Power Supply Fan Connectors (3 pins)
13) PWRCON, PWR-CON2 p.31 AT Power Supply Connector (12 pins)
14) ATXPWR p. 31 ATX Motherboard Power Connector (20 pins)
15) MSG.LED (PANEL) p. 32 LED Lead (2 pins)
16) SMI (PANEL) p. 32 SMI Suspend Switch Lead (2 pins)
17) PWR.SW (PANEL) p. 32 ATX Power Switch / Soft Power Switch (2 pins)
18) RESET (PANEL) p. 32 Reset Switch Lead (2 pins)
19)
PWR.LED (
PANEL
)
p. 32 System Power LED (3 pins)
20)
KEY LOCK (
PANEL
)
p. 32 Keyboard Lock Switch Lead (2 pins)
21) SPEAKER (PANEL) p. 32 Speaker Connector (4 pins)
22) SCSI-50/SCSI-68/ULTRA2-68 p. 33 50 pin Narrow/68 pin Wide/68 pin Ultra2 SCSI Connectors
23) SBLINK p. 34 SB-LINK™ Port Connector (6-1 pins)
24) FLOPPY p. 34 Floppy Drive Port Connector (34-1 pins)
25) COM2 p.34 Serial Port Connector (COM2, 10-1 pins)
26) VGA Memory p.35 VGA Memory Expansion Sockets
Board Layout
III. INSTALLATION
*
The onboard hardware monitor uses the address 290H-297H so legacy ISA cards must not use this
address, otherwise conflicts will occur.