Barco R9000904 Projector User Manual


 
Safety instructions
1-1
5976284 BARCOGRAPHICS 808s 150501
1
SAFETY INSTRUCTIONS
Projectors are built in accordance with the requirements of the
international safety standards IEC950, UL 1950 and CSA C22.2 No.
950, which are the safety standards of information technology equip-
ment including electrical business equipment.
These safety standards impose important requirements on the use of
safety critical components, materials and isolation, in order to protect
the user or operator against the risk of electric shock and energy
hazard, and having access to live parts.
Safety standards also impose to the internal and external tempera-
ture variations, radiation levels, mechanical stability and strength,
enclosure construction and protection against risk of fire.
Simulated single fault condition testing ensures the safety of the
equipment to the user even when the equipment's normal operation
fails.
Installation instructions
Before operating your projector please read this manual thoroughly,
and retain it for future reference.
Installation and preliminary adjustments should be performed by
qualified BARCO personnel or authorized BARCO service dealers.
OWNERS RECORD
The article number (ART. NR.) and serial number (SER. NR) are
located at the rear of the projector. Copy these numbers in the spaces
provided below. Refer to them whenever you call upon your BARCO
dealer regarding this product.
Article number :
Serial number :
Dealer :
The lightning flash with an arrowhead within a
triangle is intended to tell the user that parts
inside this product risk electrical shock to
persons.
The exclamation point within a triangle is
intended to tell the user that important operat-
ing and/or servicing instructions are included
in the technical documentation for this
equipment.
Warning :
To prevent fire or electrical shock hazard,
do not expose this projector to rain or moisture
Federal Communication Commission (FCC statement)
This equipment has been tested and found to comply with the limits
for a class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio commu-
nications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to
correct the interference at his own expense.
Instructions to the user :
If this equipment does cause interference to radio or television
reception, the user may try to correct the interference by one or more
of the following measures :
Re-orientate the receiving antenna for the radio or television.
Relocate the equipment with respect to the receiver.
Plug the equipment into a different outlet so that the equipment and
receiver are on different branch circuits.
Fasten cable connectors to the equipment with mounting screws.
Note :
The use of shielded cables is required to comply within the limits of
Part 15 of FCC rules and EN55022.
General safety instructions :
All the safety and operating instructions should be read before
using this unit.
The operating instruction manual should be retained for future
reference.
All warnings on the projector and in the documentation manuals
should be adhered to.
All instructions for operating and use of this equipment must be
followed precisely.
On safety
This product should be operated from an AC power source.
Operating AC power voltage of the projector when leaving the
factory:
The power voltage is autoranging between 100V(-10%) and
240V (+6%).
If you are not sure of the type of AC power available, consult your
dealer or local power company.
This product is equipped with a 3-wire grounding plug, a plug
having a third (grounding) pin. This plug will only fit into a grounding-
type power outlet. This is a safety feature. If you are unable to insert
the plug into the outlet, contact your electrician to replace your
obsolete outlet. Do not defeat the purpose of the grounding-type
plug.
WARNING FOR THE USERS:
THIS EQUIPMENT MUST BE GROUNDED (EARTHED) via the sup-
plied 3 conductor AC power cable. (If the supplied power cable is
not the correct one, consult your dealer.)