Dell WorkStation 410 Personal Computer User Manual


  Open as PDF
of 238
 
10-18
'HOO3UHFLVLRQ'HVNWRS6\VWHPV8VHU©V*XLGH
 8QSDFNHDFK6&6,GHYLFHDQGSUHSDUHLWIRULQVWDOODWLRQ
&$87,216*URXQG\RXUVHOIE\WRXFKLQJDQXQSDLQWHGPHWDOVXUIDFH
RQWKHEDFNRIWKHFRPSXWHU
:KHQ\RXXQSDFNWKHGULYHGRQRWVHWLWRQDKDUGVXUIDFHZKLFKPD\
GDPDJHWKHGULYH,QVWHDGVHWWKHGULYHRQDVXUIDFHVXFKDVDIRDP
SDGWKDWZLOOVXIILFLHQWO\FXVKLRQLW
Configure the device for a SCSI ID number and disable termination, if necessary.
For instructions, see the documentation that came with the SCSI device as well
as “SCSI Configuration Guidelines” found earlier in this section.
 ,QVWDOOWKH6&6,GHYLFHVDVDSSURSULDWH
To install a SCSI hard-disk drive
, complete steps 3 through 9 of “Installing an
EIDE Hard-Disk Drive in the Internal Hard-Disk Drive Bracket” found earlier in
this chapter. Then continue with step 4 of this procedure.
To install a SCSI tape drive, CD-ROM drive
,
or DAT drive
, complete steps 2
through 5 of “Installing a Drive in a 5.25-Inch Drive Bay” found earlier in this
chapter. Then continue with step 4 of this procedure.
To install an external SCSI device
, continue with step 4 of this procedure.
If you are installing a SCSI host adapter card
, configure the card and install it
in an empty expansion slot (see “Installing an Expansion Card” in Chapter 9.)
If you attach any SCSI hard-disk drives to the host adapter card, connect the
hard-disk drive access cable to the SCSI host adapter card and to the AUX
LED connector on the system board (see Figure 9-1).
 $WWDFKWKH6&6,FDEOHWRHDFK6&6,GHYLFH
For additional instructions on connecting SCSI devices, see “SCSI Cables” found
earlier in this section.
If you are installing an internal SCSI device
, firmly press the SCSI cable’s header
connector onto the 50- or 68-pin connector on the back of the device.
&$87,21<RXPXVWPDWFKWKHFRORUHGVWULSRQWKHFDEOHZLWKSLQRQ
WKHGULYH·VLQWHUIDFHFRQQHFWRUWRDYRLGSRVVLEOHGDPDJHWR\RXU
V\VWHP
The connectors on Narrow SCSI cables are keyed for proper positioning—a raised
area on the outside of the header connector fits into a notch on the device con-
nector. The connectors on Wide SCSI cables are shaped so that they can be
attached one way only.
If you are installing an external SCSI device
, connect one end of the external SCSI
cable to the SCSI bus connector on the back of the device. Attach the other end
of the external SCSI cable to the SCSI connector on the system back panel.
NOTE: Dell offers an external SCSI 68-pin-to-50-pin adapter kit for connecting
SCSI-3 devices to the SCSI-2 connector on the Precision 410 system back panel.
Contact your Dell sales representative for more information.
23186bk0.bk Page 18 Thursday, October 29, 1998 11:07 AM
 previous next