Filter
Top Products
Configuring the printer Configuring the printer
3-3 3-4
3.2 Standard Configuration 3.3 Explanation of the printout on the previous page
The standard configuration is reflected in the following printout provided that no The heading PRINT OUT gives information about the VERSION of the printer's
parameters have been changed. firmware.
PRINT OUT VERSION 202xxxxx
INTERFACE ADJUSTMENT
BUFFER 8 KBYTE AGC POSITION 24
WORD LENGTH 8 BIT PLATEN GAP 0
I/F TYPE SHARED PAPER-IN ADJ. 0 *)
BAUD-RATE 9600 BPS CUT. V-POS 0
PARITY BIT EVEN UNI-DIRECT.CMD YES
PROTOCOL DTR TRACT. FF-MODE IGNORE FF
AUTO-STATUS NO
MENU ACCESS ALL FUNCTIONS
CURRENT SETTINGS MACRO 1 MACRO 2 MACRO 3 MACRO 4*
FONT DATA DATA DATA DATA DATA
PRINT QUALITY LQ LQ LQ LQ LQ
SUB/SUPER FONT YES YES YES YES YES
PITCH 10 CPI 10 CPI 10 CPI 10 CPI 10 CPI
LINE 6 LPI 6 LPI 6 LPI 6 LPI 6 LPI
PAGE LENGTH 72 LINES 72 LINES 72 LINES 72 LINES 72 LINES
TRACTOR V-POS 0 0 0 0 0
MANUAL V-POS 0 0 0 0 0
BIN 1 V-POS 0 0 0 0 0
BIN 2 V-POS 0 0 0 0 0
BIN 3 V-POS 0 0 0 0 0
LEFT MARGIN 1 COLUMNS 1 COLUMNS 1 COLUMNS 1 COLUMNS 1 COLUMNS
RIGHT MARGIN 136 COLUMNS 136 COLUMNS 136 COLUMNS 136 COLUMNS 136 COLUMNS
TOP MARGIN 1 LINES 1 LINES 1 LINES 1 LINES 1 LINES
BOTTOM MARGIN 1 LINES 1 LINES 1 LINES 1 LINES 1 LINES
PERF. SKIP YES YES YES YES YES
PAPER SOURCE TRACTOR TRACTOR TRACTOR TRACTOR TRACTOR
PAPIER EXIT STACKER STACKER STACKER STACKER STACKER
EMULATION EPSON LQ PHILIPS GP IBM PROPR. IBM PROPR. AGM EPSON LQ
CHARACTER SET EPSON EXT.GCT NV-2.5 IBM SET 2 IBM SET 2 EPSON EXT. GCT
1: U.S.A. 1: D -NV 2.5 1: U.S.A. 1: U.S.A. 1: U.S.A.
LINE MODE LF=LF, CR=CR LF=LF, CR=CR LF=LF, CR=CR LF=LF, CR=CR LF=LF, CR=CR
$$-COMMAND NO NO NO NO NO
TEAR-OFF-MODE NO NO NO NO NO
PRE-SEPARATION NO NO NO NO NO
Note: An asterisk (’) indicates the actual macro.
*) This value is dependent on factory setting!
All this standard settings of the firmware will be restored with the menu function
RECALL FACTORY.
The next two headings are followed by two columns of standard settings:
- INTERFACE - for communication between the computer operating system
and the printer it is necessary to have the same communication settings or
features. The standard settings are:
- Buffer 8 KByte
- Word Length 8 Bit
- I/F Type Shared
- Baud Rate 9600 Bps
- Parity Bit Even
- Protocol DTR
- Auto-Status No
- ADJUSTMENT - all parameters are for adjustment of the printer and the
paper (see also the following pages).
The last part of the printout is a list with all MACRO settings. In this case
MACRO 4 is marked with an asterisk (’) which identifies it as the active macro.
If you make modifications in the active macro without saving them you will find
the new settings under the heading CURRENT SETTINGS. Unless they are
saved, the modifications will stay active only until the printer is switched off in
which case the macro settings marked with the asterisk will be reactivated.