Filter
Top Products
- 24 -
SOLID STATE RECORDER PMD671
POWER
MIC ATTEN
0dB -20dB
FLAT
ANC
LEVEL CONT.
LIMITER
ALC MANUAL
OFF
ON
EDL PLAY
STEREO
L
AUDIO OUT
R
SOURCE FILE
MONITOR
OFF ON
PRE REC
MARK
A-B REPEAT
INPUT
EDIT
SINGLE
OFF
ALL
OFF
ON
INPUT LOCK
TRACK JUMP
MARGIN RESET
REC
UNDO
MENU/STORE ENTER CANCEL
PLAY / PAUSE STOP
USB
-
/
REW
FWD
/
+
TRACK JUMP
MARGIN RESET
REC
UNDO
MENU/STORE
ENTER
CANCEL
PLAY / PAUSE STOP
USB
-
/
F.REV
F.FWD
/
+
MIC
INT
TRACK
TIMETRACK
-dB
00
40
20 12
62
0
over
-dB
R
L
level margin
MENU/STORE
MARGIN RESET
USB
23
SOLID STATE RECORDER PMD671
POWER
MIC ATTEN
0dB -20dB
FLAT
ANC
LEVEL CONT.
LIMITER
ALC MANUAL
OFF
ON
EDL PLAY
STEREO
L
AUDIO OUT
R
SOURCE FILE
MONITOR
OFF ON
PRE REC
MARK
A-B REPEAT
INPUT
EDIT
SINGLE
OFF
ALL
OFF
ON
INPUT LOCK
TRACK JUMP
MARGIN RESET
REC
UNDO
MENU/STORE ENTER CANCEL
PLAY / PAUSE STOP
USB
-
/
REW
FWD
/
+
TRACK JUMP
MARGIN RESET
REC
UNDO
MENU/STORE
ENTER
CANCEL
PLAY / PAUSE STOP
USB
-
/
F.REV
F.FWD
/
+
a b
d c
Controls and Connections
Top continued
MARGIN RESET button
During record, press and release to reset the
peak level margin.
Example display
with level margin at
OV before pressing
the MARGIN RE-
SET button.
The level margin displays the highest level
achieved since the track began, or the MARGIN
RESET button was pressed and released. OV
indicates a margin over 0dB.
USB button
Connects the CF card via the USB port to a
connected device (usually a computer).
From power off, press and hold the USB button
while you slide the PMD671's POWER switch to
the right.
This display
appears.
The CF card in the PMD671 appears as an
external drive on a connected computer.
Power off to disconnect.
See page 51, How to connect via the USB port.
MENU/STORE button
Press and hold for about 2 seconds to enter
menu mode.
Press and release during menu operations to
store the changed values.
Menu operations
Menu operations let you fine tune how the
PMD671 is set up, including the recording pa-
rameters for your specific recording situation.
The PMD671 is always recording using Preset1,
2 or 3. To modify the recording setup, you modify
one of those three presets.
The Menu procedure starts with selecting one of
the Presets, then modifying either the settings
within that Preset, or the General settings for
Date and time, date format, beep and/or battery
type.
1. Press and hold the
MENU/STORE button
(a) for about 2 seconds. Preset will appear
(flashing) in the display.
Example
display
Press ENTER
......save & switch to next item
Press
MENU/STORE .....................save & exit
Select Preset
Quick instructions
Press & hold
MENU/STORE 2 sec ....... Preset
Press ENTER
................................... Preset#
Press F.FWD/+
..................................... set #
23. MARGIN RESET/
USB
MENU/STORE
buttons
Several functions depending
on state of the PMD671.
2. While Preset is flashing, press and release
the ENTER button
(b).
The flashing
switches to the
Preset choice.
continues