Mitsubishi Electronics 2404f Network Card User Manual


 
Tag Addresses 2408
f
& 2404
f
PROFIBUS Communications Handbook
8-2 2408
f
& 2404
f
PROFIBUS Communications Handbook
9 Reserved
10 Reserved
11 Reserved
12 Reserved
13 Reserved
14 Reserved
15 Reserved
Program Logic Status 162
BIT DESCRIPTION
0 Program Output 1 ( 0 = OFF 1 = ON )
1 Program Output 2 ( 0 = OFF 1 = ON )
2 Program Output 3 ( 0 = OFF 1 = ON )
3 Program Output 4 ( 0 = OFF 1 = ON )
4 Program Output 5 ( 0 = OFF 1 = ON )
5 Program Output 6 ( 0 = OFF 1 = ON )
6 Program Output 7 ( 0 = OFF 1 = ON )
7 Program Output 8 ( 0 = OFF 1 = ON )
8 Reserved
9 Reserved
10 Reserved
11 Reserved
12 Reserved
13 Reserved
14 Reserved
15 Reserved
Digital Output Status Word 551
BIT DESCRIPTION
0 H Interface module telemetry (0 = Off, 1 = On)
1 J Interface module telemetry (0 = Off, 1 = On)
2 1A module telemetry (0 = Off, 1 = On)
3 LB logic telemetry (0 = Off, 1 = On)
4 LA logic telemetry (0 = Off, 1 = On)
5 1B module telemetry (0 = Off, 1 = On)
6 1C module telemetry (0 = Off, 1 = On)
7 2A module telemetry (0 = Off, 1 = On)
8 2B module telemetry (0 = Off, 1 = On)
9 2C module telemetry (0 = Off, 1 = On)
10 3A module telemetry (0 = Off, 1 = On)
11 3B module telemetry (0 = Off, 1 = On)
12 3C module telemetry (0 = Off, 1 = On)
13 AA relay telemetry (0 = Off, 1 = On)
14 Reserved
15 Reserved
Digital Input Status Word 87
BIT DESCRIPTION
0 H Interface module (0 = Off, 1 = On)
1 J Interface module (0 = Off, 1 = On)
2 1A module (0 = Off, 1 = On)
3 LB logic input (0 = Off, 1 = On)
4 LA logic input (0 = Off, 1 = On)
5 1B module telemetry (0 = Off, 1 = On)
6 1C module (0 = Off, 1 = On)
7 2A module (0 = Off, 1 = On)
8 2B module (0 = Off, 1 = On)
9 2C module (0 = Off, 1 = On)
10 3A module (0 = Off, 1 = On)
11 3B module (0 = Off, 1 = On)
12 3C module (0 = Off, 1 = On)
13 Reserved
14 Reserved
15 Reserved
Parameter Description Tag
Address
SP Rate Limit Holdback Status
0: Inactive
1: Active
41
Pot Break 350
Freeze Control Flag
0: Controlling
1: Hold
257
SP Rate Limit Active Status
0: No setpoint rate limit
1: Setpoint rate limit active
275
Sensor Break Status Flag
0: Good
1: Sensor break
258
Power Failed flag
0: Good
1: Power fail detected
259
New Alarm Flag 260
Loop Break Status Flag
0: Good
1: Loop break
263
Integral Hold Status Flag
0: Good
1: Integral hold
264
SRL Complete Status
0: Setpoint rate limit incomplete
1: Setpoint rate limit complete
277
Remote Input Status Flag
0: Good
1: Fault
280
Sync Continue Flag
0: Continue
1: Awaiting synch
281